Where Does Red Wire of Brake Controller Install Harness 3023-P Install on 2014 Ram 2500

Question

Question:

We currently have a 2014 2500 Ram that came with a break up controller. We’ve had no luck with it. We purchased a P2 along with Tekonsha 3023-P. We found the plug-in for the main wires. Can’t seem to locate the plug for the red wire. I’m sure it’s already plugged into an OEM for the brakes.

asked by: Ron H

0

Expert Reply:

I attached a picture that shows where the red wire installs of the brake controller install harness part # 3023-P but the easiest way to find it will be to watch the video I attached that shows how to find it as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I called my contact at Tekonsha and asked about replacing the Dodge Integrated Brake Controller if the truck is a 2010 through 2015. If you have a different year Ram just let me know and I can make some recommendations that will work for you. They…

view full answer...

Answer 2

To install the #3023-P harness into your 2014 Ram 3500 you'll need to unplug the factory brake controller and use the same connector. Then the second 2-pin connector will normally be just above the brake pedal. If you check out the linked video…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 6

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 11

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 12

Hey Brandon, I would strongly recommend sticking with the Tekonsha RF brake controller part #TK94FR. We know this works really well and it sounds like it worked well for you too. The Curt Echo is not reliable enough for me to really ever recommend it…

view full answer...

Where Does Red Wire of Brake Controller Install Harness 3023-P Install on 2014 Ram 2500

Featured Help Information

Miscellaneous Media

Continue Researching