Locking Lug Nut Recommendation for Roadmaster Tow Dolly # RM-2050-1

Question

Question:

The instructions dont say what the thread size is. Thanks!

asked by: Monica I

0

Expert Reply:

The lug nuts on the dolly are 1/2 inch diameter lugs like what trailers often use so the correct locking lug nuts would be the part # RG01-150.

expert reply by: Jameson C

0

Answer 1

I have an answer for you. I went ahead and reached out to my contact at Demco, and he said that depending on the ratchet-style you have on your 2019 Stahl dolly, you might need a different style of strap than the Demco Strap #DM03528-93 to fit your…

view full answer...

Answer 2

There is a retainer bolt in the wheel carrier that holds the bushing and king pin in place in the Demco Kar Kaddy SS #DM9713045. You would need to remove the retainer bolt to release the king pin and replace it. This is a part that we do not…

view full answer...

Answer 3

I checked with Roadmaster and the Pivot Bolt part #RM-350800-00 of the Roadmaster Tow Dolly part #RM-2050-1 needs to be torqued to 70 ft lbs. Loc Tite is not recommended.

view full answer...

Answer 4

The Replacement Pivot Bolt for Roadmaster Tow Dolly with Electric Brakes - Qty 1 #RM-350800-00 as you stated does not come with any additional hardware. Currently the only way to get the bolt and nut is to get the Roadmaster Tow Dolly Ramp Wear Strip…

view full answer...

Answer 5

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Locking Lug Nut Recommendation for Roadmaster Tow Dolly # RM-2050-1

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching