Where Is The Brake Controller Plug On a 2019 Mercedes-Benz Sprinter 2500

Question

Question:

Is the 3030-p the correct harness to hook up my p3 to a 2019 sprinter 2500 with factory trailer hitch? I have my van on order but wanted to be ready for when it arrives.

asked by: Ram M

1

Helpful Expert Reply:

Yes, the Tekonsha Custom Wiring Adapter for Trailer Brake Controllers part # 3063-P is the correct harness that will allow you to use the Tekonsha Prodigy P3 Trailer Brake Controller part # 90195 on your 2019 Mercedes-Benz Sprinter 2500 without splicing.

The plug that the harness will use is located under the driver seat. It is a green four pin plug which can be seen in the attached photo.

expert reply by: Conner L

1

click to enlarge

Philip S.

3/16/2020

Will this also fit the 3500 sprinter

Chris R.

3/17/2020

Yep! The Plug-In Harness # 3063-P mentioned above is the correct part for your 2019 Mercedes Springer 3500 as well.

Bob H.

7/13/2020

to connect the #3063-p is it necessary to remove the driver's seat to get access to the green plug beneath? I can't really see it with the seat in place.

Chris R.

7/18/2020

I've not heard of that being necessary. You may need to pull down the factory plug a bit to really gain access to it - sometimes they are actually tapped to a nearby harness.

Dave C.

3/3/2021

@ChrisR On my 2017 Sprinter 3500 this plug was tucked under the fuse board directly below the hatch/door on the drivers side seat. It is impossible to see. I found it with a fiber optic inspection camera.

Jon G.

3/5/2021

@DaveC Thank you for your input!

See All (4) Replies to Bob H. ∨

Answer 1

I checked with Tekonsha and a few other brake controller manufacturers and they state that your 2024 Mercedes Sprinter 3500 does not have an OEM brake controller install port under the dash like previous models so you would have to hardwire in the…

view full answer...

Answer 2

Hey Darin. I checked with Curt and their 52109 wiring harness is the correct one for your 2025 Chevy Trax Activ. This is going to give you a 4-way connection so your RV can control your Trax's lighting functions. I saw you have already purchased…

view full answer...

Answer 3

If you're talking about the two dots on the left side of the Brake Buddy Stealth #HM39530 controller (A) those are mode indicator lights that will display regardless of whether the towed vehicle or trailer is connected. You'll want to test…

view full answer...

Answer 4

Switching from a hydraulic braking system to electric on a trailer is actually a lot less complicated than the other way around. You basically just need to lock out your surge brake actuator, swap out your brakes and hubs, and then add some wiring…

view full answer...

Answer 5

As long as your 2019 Mercedes-Benz Sprinter 2500 has a factory plugin connection point for the adapter part #3063-P you will not need to make any modifications to the adapter, it will plug right in into the factory plug and the other end to a…

view full answer...

Answer 6

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 7

It sounds like you might be searching for some replacement electric trailer braking assemblies or possibly just replacement parts. It's typically not much less cost effective to just replace the entire assembly so that's what I recommend. I…

view full answer...

Answer 8

Hello Mike. It sounds like you are wanting to add electric brakes to your boat trailer that currently has no brakes. This is possible, but you will first need to make sure that your axle is equipped with a brake flange at the base of the spindle. The…

view full answer...

Answer 9

You can hard-wire in a brake controller, and it seems that there are not a lot of the Sprinter 3500 models that are pre-wired, at least from what I've seen in my research. I have not seen any reports that this isn't possible, and we even have…

view full answer...

Answer 10

The grease zerk fittings on a Dexter EZ-Lub Axle are threaded. If you broken off the one you have now you can use a screw/bolt extractor to remove the remaining threads and then use the Replacement Grease Zerk part #Gzerk to replace it which I can…

view full answer...

Answer 11

EZ Lube Dust Caps, like #DC200L-DCRP, have a rubber plug that can be removed to access the zerk fitting. The rubber plug can be removed by gently prying it up with a flathead screwdriver. If your dust cap is in good condition and you want to avoid…

view full answer...

Answer 12

Hey Graham! It looks like the Sunseeker is built on the Sprinter 3500 chassis, I recommend verifying that to be sure. For a brake controller I recommend the Redarc Tow-Pro Liberty #RED24FR. This is simple, reliable, and doesn't take up any space…

view full answer...

Where Is The Brake Controller Plug On a 2019 Mercedes-Benz Sprinter 2500

Continue Researching