Height of Vertical Square Tube on RockyMounts BackStage 2 Bike Rack # RKY10002

Question

Question:

My off-road trailer has the trailer side of the hitch Max Coupler mounted in a 2inch receiver tube. I may need some more tongute length to allow for mounting a bike rack using the Curt Multipurpose Ball Mount with 2inch Receiver. Can I simply extend my trailer tongue using a hitch extension? I imagine that would have the effect of reducing the tongue weight on the vehicle side, but is there anything else I need to consider? Im towing with a 2016 Toyota Tacoma Dbl-cab Off-Road with the tow package, which has some sway control built into truck. It also has towing capacity of 6500# and tongue weight of 650# so Ill be well within that.

asked by: Kevin K

1

Helpful Expert Reply:

From the center of the hitch pin hole to the top of that small vertical post at the end of the shank on the RockyMounts BackStage # RKY10002 there is a distance of 4-3/8 inches. I have attached an image to assist. You can use this measurement to ensure the tailgate on your Tacoma will drop all the way down with the rack attached and the platform swung away to the side.

I have included a short video demonstration on this carrier that you can check out as well.

expert reply by: Chris R

1

click to enlarge

Kevin K.

3/5/2019

My off-road trailer has the trailer side of the hitch Max Coupler mounted in a 2inch receiver tube. I may need some more tongute length to allow for mounting a bike rack using the Curt Multipurpose Ball Mount with 2inch Receiver. Can I simply extend my trailer tongue using a hitch extension? I imagine that would have the effect of reducing the tongue weight on the vehicle side, but is there anything else I need to consider? Im towing with a 2016 Toyota Tacoma Dbl-cab Off-Road with the tow package, which has some sway control built into truck. It also has towing capacity of 6500# and tongue weight of 650# so Ill be well within that.

Chris R.

3/5/2019

Using an extender like the Curt 8" # C45791 will provide you with the clearance you need but it will indeed reduce the weight capacities of your trailer hitch. In fact, the Curt Multipurpose Ball Mount # D210 that you also plan on using in order to pull a trailer at the same time will do this as well since it is adding a second connection point. Each adapter when used by itself will technically reduce the weight capacity of your hitch by 50 percent so using the two together is not really recommended. This is going to create a lot of movement during travel. A better option will be to just use a single adapter that is longer so you can obtain the length you need with just one component (thus only reducing the capacity of your hitch by 50 percent). For this I recommend taking a look at the Malone Dual Hitch Extender # MPG544. This will provide you with two 2 inch receivers on which the bottom opening can be used for your ball mount to pull your trailer. There is a distance of 12-3/8 inches from the hitch pin hole to the hitch pin holes on the dual receivers (this dimension on the Curt # D210 is 7-1/2 inches). As long as the combined weights of your trailer and loaded bike rack do not exceed the reduced ratings on your hitch when using the adapter this solution will work great. If your hitch has a 6,500/650 pound rating like you mentioned then they will be reduced to 3,250/325 pounds.

Answer 1

I have a similar solution that can be used with a bike rack with the Roadmaster High Low Adapter part #RM-076 but the Blue Ox can only be used when flat towing a vehicle.

view full answer...

Answer 2

It is not recommended to invert the Malone 2" Dual Purpose Hitch Receiver #MPG544 for towing purposes. The extended receiver is only intended for accessory use not for a ball mount and trailer connection. Your trailer hitch's tongue weight…

view full answer...

Answer 3

Though this technically will work when looking at all the measurements, I cannot recommend doing so. Here's my reasoning behind saying that. With your fully loaded trailer having a tongue weight of 315 pounds and your loaded bike rack weighing 50…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Height of Vertical Square Tube on RockyMounts BackStage 2 Bike Rack # RKY10002

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching