Replacement Striker Pin and Bracket for UWS Truck Tool Box

Question

Question:

Can I get the striker pin as well for Replacement Striker Bracket for UWS Truck Tool Boxes - Qty 1 Item # UWS-SBRACKET?

asked by: Mike

0

Expert Reply:

The Replacement Striker Bracket for UWS Truck Tool Boxes - Qty 1 # UWS-SBRACKET will use the Replacement Nail Head Striker Pin for UWS Boxes with Paddle Handles - 1/4" Diameter # C003-NHPIN.

expert reply by: Jason S

0

Answer 1

The side of the #UWS-SBRACKET where you would mount the #C003-NHPIN is 2-3/8" long. The hole where the pin mounts measures 2" long. The side with the mounting holes measures 2-3/8" x 1". See the attached image below.

view full answer...

Answer 2

The folks at Bolt tell me if their #BL7023547 lock would be compatible with UWS and DeeZee toolboxes, but they were unable to specify fit for a Kobalt toolbox, but if the latches you currently have match the dimensions of the diagram I've…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Hi Doug! If you were just needing a weight distribution system for the sway control, I would have said the Andersen Weight Distribution Hitch w Sway Control - 6" Drop/Rise - 14K GTW, 1.4K TW #AN53VR could be a good option. However, I have tried…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Travis, welcome back! You're friend makes a good point the only way to lock the B&W Companion OEM 5th Wheel Hitch item #BWRVK3305 is to use a padlock like item #Master Lock 1-9/16" Wide Solid Brass Body Padlock item #ML140DLH. The…

view full answer...

Answer 11

Hey Chris, in the instructions for the B and W Turnoverball gooseneck hitch part #BW73FR that you referenced it says that the inner brackets are not needed if the truck has the inner brackets for the OEM hitch already welded to the truck frame. In…

view full answer...

Replacement Striker Pin and Bracket for UWS Truck Tool Box

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching