How long does It Take to Hardwire a Tekonsha P3 Electric Brake Controller On a 2008 Chrysler Aspen
Published 11/17/2011 >
Products Featured in This Question
Question:
Hi! ... New to RVing ... will be having my dealer install the P3 for my new TT. Can you tell me about how long a professional install should take? I believe the unit will need to be hard wired into my 2008 5.7 V-8 Chrysler Aspen, since I do not have the factory tow package on my vehicle. Much appreciated.
asked by: John
Expert Reply:
Installation time is going to vary by shop and the experience of their mechanics. If you are going to an RV dealer that has experienced mechanics that have done hard wire installations several times in the past, I would say that the install time for the P-3 brake controller, # 90195, the 4-Way wiring harness, # 118390, and the brake controller installation kit, # ETBC7, will require 3-1/2 to 4 hours of install time.
Here at our facility we do video installations and the time required for each install is much longer, so we do not have a specific answer for you.
We do have an installation video of the # 118390 Wiring harness, the # ETBC7 brake controller install kit and a brake controller on a 2008 Chrysler Aspen without towing package for you to review. These videos, along with the instructions included with the items, see links, would allow you to complete a professional looking installation right at home, if you were up to the challenge and have the time to do the install. For a novice installer you should probably allow a full morning and afternoon for the install so you can take your time and avoid mistakes from trying to hurry. This install is pretty straight forward and the items listed are all you will need to complete the installation.
Featured Help Information
Miscellaneous Media




Continue Researching
- Shop: Brake Controller
- Q&A: Brake Controller for 2024 Nissan Pathfinder Towing Trailer with Electric Over Hydraulic Brakes
- Shop: 7-Way RV Upgrade Kit for Trailer Brake Controller Installation - 12 Gauge Wires
- Shop: Pollak Circuit Breaker - Cycling/Automatic Reset - 40 Amp - Straight Mount Bracket
- Shop: 40 Amp In-Line Circuit Breaker - Perpendicular Mount Bracket
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Curt Trailer Connector Adapter - 4-Way to 7-Way RV and 4-Way Flat
- Shop: 10 Gauge Wire - Blue Primary - Per Foot
- Shop: Curt Universal Installation Kit for Trailer Brake Controller - 7-Way RV - 10 Gauge
- Search Results: 4 way to 7 way adapter
- Search Results: 12 gauge wiring
- Search Results: 30 amp circuit breaker
- Search Results: 10 gauge wire
- Search Results: trailer brake controller
- Search Results: 3430001
- Search Results: 40 amp circuit breaker
- Q&A: What is the Difference Between the ETBC7 and Curt 57672
- Q&A: Can 20 Amp Fuse Replace 40 Amp Breaker on ETBC7L Installation
- Q&A: Is Smaller 12 Volt Wire on Curt 4-Way to 7-Way Adapter an Issue
- Q&A: Does 12 Volt Power Circuit of 7-Way Adapter Have to Run Up to Vehicle Battery
- Q&A: What Gauge Wire To Use For Power Wire On 7-Way?
- Q&A: Can 7-Way Adapter Power Wire Be Same Wire as 4-Way Converter Box
- Video: Tekonsha Prodigy P3 And Curt Echo Under Dash Brake Controller Comparison
- Video: A Closer Look at the 30 amp. In-Line Circuit Breaker
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Article: How to Measure for Trailer Hitch Drop
- Video: Redarc Tow-Pro Liberty Brake Controller Review RED24FR