What Size Bolt is Used with the Erickson Spare Trailer Tire Bracket Kit 77316

Question

Question:

Need to know the bolt diameter and thread on the EM77316 spare tire mount

asked by: Martin

0

Expert Reply:

I spoke with Erickson Manufacturing about the Erickson Spare Trailer Tire Bracket Kit part # EM77316 and they informed me that the bolt included with this kit is a 5/16"-20x6". The "5/16" is the diameter in inches, the "20" is the thread pitch, and the "6" is the length in inches.

expert reply by: Conner L

0

Answer 1

The 023-106-00 brake you have pictured is going to be the Dexter 12 Inch Right Hand #23-106. As it is best to do both sides when replacing brakes, I suggest going with #23-105-106. This replaces both the driver and passenger sides and will be direct…

view full answer...

Answer 2

You would not be able to charge your battery through the wiring on your 4-way trailer connector. Since your truck has a 7-way connector, you could maintain the power to the battery but not charge it. To begin, you would need to cut off your 4-way…

view full answer...

Answer 3

To charge the battery in the Engager Trailer BreakAway Kit, #20099, you can attach the wire from the 12 volt circuit on the trailer side 7-Way (1 oclock position on the back of the trailer side 7-Way where the wires attach) to the input wire on the…

view full answer...

Answer 4

If you have a break away kit that does not include a charger, you can provide a charge to the battery using the 12 volt circuit or auxiliary circuit from the vehicle 7-Way trailer connector. However, using the 7-Way can overcharge a break away…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

What Size Bolt is Used with the Erickson Spare Trailer Tire Bracket Kit 77316

Product Page this Question was Asked From

Continue Researching