Slide Topper Recommendation for Flange Width of 74 inches

Question

Question:

My slide is 74inch from flange to flange will the 61/2 foot topper work or should I get the 7foot topper

asked by: David

0

Expert Reply:

Since your flange width is 74 inches the correct Solera slide topper is the part # LCV000163285 as it was designed to fit flange widths between 74-79 inches. This is the 7 foot size.

expert reply by: Jameson C

0

Answer 1

The access plate is 2-15/16" wide and 7-5/8" long and must be mounted on the slide out's outside wall as far up as it can, but not mounted on the t-molding. The t-molding is what looks like 6" wide trim around the outside slide out…

view full answer...

Answer 2

The measurement you need to pick out a slide out awning for a motorhome like your 2002 Winnebago Journey DL is the width that includes the flange around the outside of the slide out. For example the #LCV000165061 is the correct fit for flange widths…

view full answer...

Answer 3

The 8' size listed is the width of the entire awning, end to end. The awning also extends up to 50” over the slide out. I've attached a photo indicating what these dimensions include. To calculate the size you need, determine your slide-out…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Slide Topper Recommendation for Flange Width of 74 inches

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching