7-Way Trailer Wiring Harness Recommendation for 2008 Toyota Tundra

Question

Question:

I broke the connector, need to replace it, need both fmale and female

asked by: Jd

0

Expert Reply:

Looks like you broke the 7-way of your 2008 Toyota Tundra. For a replacement we have the Hopkins kit part # HM11143395 which is an exact replacement for what you have and would work great. I attached an install video for the harness on a similar 2008 Tundra as well.

expert reply by: Jameson C

0

Answer 1

The correct replacement 7-way for your Tundra should be part #HM43385. You can confirm this by examining the connectors under the truck that the connector would plug into. One connector should accept 4 pins, the other three pins. If your connectors…

view full answer...

Answer 2

There will be a fuse and/or relay associated with the 12 volt accessory circuit of the 7-way on your 2007 Toyota Tundra. Check under the hood of the truck for that circuit and replace as needed. Your other option is to run a 10 gauge wire from the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

7-Way Trailer Wiring Harness Recommendation for 2008 Toyota Tundra

Featured Help Information

Miscellaneous Media

Continue Researching