Trailer Hitch Compatibility with 2002 Dodge Ram 2500

Question

Question:

2002 dodge 2500 p/u what is ment by roll pan bumper ,bumper on truchk has frame work behind it ,rolled crome steel cover ?????

asked by: Wayne T

0

Expert Reply:

The Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" # 75101 will not fit models with the roll pan bumper. This bumper is molded and normally painted to match the truck and be flush with the tailgate like the attached photo. Your bumper is not a roll pan based on your question, so you can use the Draw-Tite # 75101.

expert reply by: Jason S

0

click to enlarge

Answer 1

The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…

view full answer...

Answer 2

The size of the bolts that come with the Draw Tite hitch part #75101 that you referenced are 1/2-13x1-3/4 Grade 5. You can order this hardware kit from us as part #RHK.

view full answer...

Answer 3

The Universal Wiring Harness w/ ModuLite and Brake Controller Harness part #22551 will work to add a 7-way to a 1996 Dodge Ram. This kit comes with everything you need for the above and you should not have to extend any wires. In order to have both 4…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Trailer Hitch Compatibility with 2002 Dodge Ram 2500

Continue Researching