Cost Effective Roof Rack Recommendation for 2011 Honda Accord

Question

Question:

Will the Rhino rack 2500 fit better than Sportrack sr1010 for an Accord 2011? Thanx!

asked by: Jean-Vincent

0

Expert Reply:

What we've found with the Sportrack Semi-Custom roof racks like the part # SR1002 is that they don't always fit the best. Reason being they are designed to fit as many vehicles as possible which means they don't fit everything perfectly. The price makes these hard to not be tempted by, but your best option is a fully custom fit roof rack like the Inno part # INB127, # INSUT, and # INK745 otherwise you'll have to get somewhat creative to get the Sportrack to fit right.

expert reply by: Jameson C

0

Jean-vincent

10/1/2018

Will the Rhino rack 2500 fit better than Sportrack sr1010 for an Accord 2011? Thanx!

Jameson C.

10/1/2018

Yes, the Rhino Rack roof racks like the rack that fits your Accord part numbers # RRVA126B-2, # RRRLKVA, and # DK184 will fit much better than the Sportrack roof rack you tried. Rhino Rack roof racks typically cost a bit less than the most expensive brands but they fit and perform just as well. This would be a huge step up over the Sportrack. This rack I mentioned is an aero bar roof rack. For a square bar roof rack instead you'd want the part numbers # RRVA126B-2, # RRRLKVA, and # DK184. This will cost a bit less than the aero bar option.

Answer 1

I have a great crossbar solution for you to use the Inno Locker #INXA445! For your 2004 Honda Accord 4-door with a naked roof, the Inno Locker will attaches as long as you have aero crossbars that have top channels that extend the length of the…

view full answer...

Answer 2

The Inno Box 2020 Rooftop Cargo Box #IN86FR will fit as long as you have the required 24"-39" crossbar spread. You will need to measure to be sure. Also yes, this will fit on the Inno Aero Crossbars #INXB130-2.

view full answer...

Answer 3

Yes, to complete a roof rack for your 2011 Honda Accord Coupe all you would need is the two Rhino Rack part numbers that you referenced, part #RRVA126B-2, #RRRLKVA and #DK151. I attached an install video that shows these two part numbers being used…

view full answer...

Answer 4

The Yakima SkyBox NX 16 Rooftop Cargo Box - 16 cu ft - Black Carbonite #Y95AV has crossbars that are adjustable from 24-36 inches on center for your crossbar spread. The maximum crossbar dimensions are 3-1/2" wide x 1-11/16" tall. This…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Cost Effective Roof Rack Recommendation for 2011 Honda Accord

Products Featured in This Question

Continue Researching