Can Jensen 8 Amplified Subwoofer with Enclosure # JMPSW800 Connect to RV Stereo Head Unit

Question

Question:

Would this work with a jensen jwm70a cd/dvd player?

asked by: Aaron P

1

Helpful Expert Reply:

Yes, your Jensen stereo has RCA outputs that you could run to the RCA inputs of the Jensen 8" Amplified Subwoofer with Enclosure # JMPSW800 and it would work well.

expert reply by: Jameson C

1

Answer 1

I assume you are referring to the Jensen Marine Amplified Subwoofer part #JMPSW800. If that is the case then I have attached the correct wiring diagram for you. There are a set of red/white RCA cables that will go to a stereo like the Furrion Stereo…

view full answer...

Answer 2

The wiring harness for the Jensen Enclosed Amplified Marine Subwoofer #JMPSW800 has a 3-wire pigtail for you to splice in your power, ground, and remote. You would just need to cut the wire down to necessary length and splice it to the remote wire…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 10

Hey Jairo. So we do not offer a direct replacement for the Norcold N611, but we do have a good replacement option for you. It really comes down to what will fit in your cutout space. Take a look at the Norcold RV Refrigerator w/ Freezer - 8.2 cu ft -…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Can Jensen 8 Amplified Subwoofer with Enclosure # JMPSW800 Connect to RV Stereo Head Unit

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching