Picking Out Bearing Kit for Trailer with 2,000 lb Axles

Question

Question:

I need to replace the bearings model is st6208ua five lug 13inch rim 2000lbs axle

asked by: Michael E

1

Helpful Expert Reply:

Nearly all 2,000 lb axles have a spindle that is 1 inch in diameter where both bearings ride. If that's what you have then the bearing kit part # BK1-100 would be what you need as it fits that spindle.

expert reply by: Jameson C

1

click to enlarge

Answer 1

Hey Kyle, Sure can, and the correct Bearing Buddies for the Malone MicroSport Trailer #MPG460G are the Bearing Buddy Bearing Protectors #BB1980A-SS.

view full answer...

Answer 2

Hey Richard, the correct bearing kit would be the part #BK1-150 since your spindles are 1-1/6 inch in diameter for both bearing surfaces. The correct Bearing Buddies for the Malone MicroSport Trailer #MPG460G are the Bearing Buddy Bearing Protectors…

view full answer...

Answer 3

Hey Jeffrey! The Malone MicroSport Trailers like item #MPG462G2 have a 1" straight spindle. To upgrade the bearings you would need two of the Bearing Kit for 1" BT8 Spindle, L44643 Inner/Outer Bearings, 34823 Seal item #BK1-100.

view full answer...

Answer 4

Yes you can get new tires for your Malone MicroSport trailer with a speed rating higher than the 65 mph rating of the tires it comes with. For the same size 4.80-12 tires with an 81 mph speed rating use the following: - Taskmaster 4.80-12 Radial…

view full answer...

Answer 5

We actually carry the spare tire that fits the Malone MicroSport Trailer #MPG460G. The spare is #MPG465 and does have a 5 on 4-1/2 bolt pattern. With that being said it would be more cost effective for you to purchase two 4.80-12 trailer tires, like…

view full answer...

Answer 6

Yes, we do have the conversion kit. - Malone MicroSport to LowBed Trailer Conversion Support Tubes #MAL33TR The Malone MicroSport to LowBed Trailer Conversion Support Tubes #MAL33TR works to convert your Malone MicroSport or MicroSportXT trailer to a…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Picking Out Bearing Kit for Trailer with 2,000 lb Axles

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching