Bearing Kit and Bearing Buddy that Fits Malone MicroSport Trailer

Question

Question:

I have a 2016 Malone MicroSport trailer. The VIN in 4KF 621413 GG 001483 The spec sheet indicates a 1-1/16” spindle. I plan to Lucas Oil Multi-Purpose Marine Grease. Could you please verify the part numbers for both the wheel bearing replacement kit and bearing buddy kit for this trailer? Thank you!

asked by: Richard C

0

Expert Reply:

Hey Richard, the correct bearing kit would be the part # BK1-150 since your spindles are 1-1/6 inch in diameter for both bearing surfaces.

The correct Bearing Buddies for the Malone MicroSport Trailer # MPG460G are the Bearing Buddy Bearing Protectors # BB1980A-SS.

How do you like the MicroSport so far?

expert reply by: Jameson C

0

Richard C.

3/9/2026

Hello Jameson, Excellent, thank you! Have ordered and expected in a few days. Recently purchased and haven’t used the MicroSport yet. I’ve replaced the wiring harness and converted it to the LowBed configuration. Made two sets of 6’ bunks. Just installed new tires and with the bearing kit replacement and bearing buddy it’ll be as good as new! Thanks again!

Jameson C.

3/9/2026

@RichardC Glad to help! Thats quite the overhaul!

Richard C.

3/10/2026

@JamesonC Say, I wanted to share this idea with you. The MicroSport I purchased has a retractable tongue. I found these Magnetic Zip Tie Mounts with zip ties on Amazon. They are strong magnets that hold very well. It allows you to easily remove and coil up the harness when retracting the young for storage!

Jameson C.

3/10/2026

@RichardC that's really cool thank you for sharing!

Answer 1

Hey Jeffrey! The Malone MicroSport Trailers like item #MPG462G2 have a 1" straight spindle. To upgrade the bearings you would need two of the Bearing Kit for 1" BT8 Spindle, L44643 Inner/Outer Bearings, 34823 Seal item #BK1-100.

view full answer...

Answer 2

Nearly all 2,000 lb axles have a spindle that is 1 inch in diameter where both bearings ride. If that's what you have then the bearing kit part #BK1-100 would be what you need as it fits that spindle.

view full answer...

Answer 3

Yes, we do have the conversion kit. - Malone MicroSport to LowBed Trailer Conversion Support Tubes #MAL33TR The Malone MicroSport to LowBed Trailer Conversion Support Tubes #MAL33TR works to convert your Malone MicroSport or MicroSportXT trailer to a…

view full answer...

Answer 4

We actually carry the spare tire that fits the Malone MicroSport Trailer #MPG460G. The spare is #MPG465 and does have a 5 on 4-1/2 bolt pattern. With that being said it would be more cost effective for you to purchase two 4.80-12 trailer tires, like…

view full answer...

Answer 5

Yes you can get new tires for your Malone MicroSport trailer with a speed rating higher than the 65 mph rating of the tires it comes with. For the same size 4.80-12 tires with an 81 mph speed rating use the following: - Taskmaster 4.80-12 Radial…

view full answer...

Answer 6

Hey Richard, what you did is closer to the correct way than shooting for a torque spec. This is what we generally recommend: The nut is ran down until there is no side to side play in the hub, and then backed off to the next notch in the castle nut…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Bearing Kit and Bearing Buddy that Fits Malone MicroSport Trailer

Products Featured in This Question

Continue Researching