How to Find Breakaway Battery on Fifth Wheel Camper

Question

Question:

where is the breakaway switch battery located located on my 2000 Dutchman lite rv

asked by: Bill A

0

Expert Reply:

I really wish we had a diagram or a way to pull up where it'd be. Most likely under the overhang near the landing gear jacks as that's the most popular place. Check there first and then trace the wiring from the breakaway switch to see where they go as they will lead to the battery.

expert reply by: Jameson C

0

click to enlarge

Answer 1

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 2

You're already on the right track with everything you looked at. Your 2018 Thor ACE 30.3 has a GVWR of 18,000 lbs so I recommend the following: -Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets for Class A Motorhomes #RM33RR…

view full answer...

Answer 3

I called Air Lift to confirm, and you are correct in that the LoadLifter 5000 Ultimate Air Springs, part #AL88240, are not compatible with your 24,000-lb chassis. We do, however, have springs that are compatible. They are the SumoSprings Rebel Custom…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

How to Find Breakaway Battery on Fifth Wheel Camper

Featured Help Information

Miscellaneous Media

Continue Researching