Recommended Torque Specs for Motorhome Lug Nuts

Question

Question:

Need to know the rear lug nut tourque 2009 Fleetwood icon

asked by: Shelley G

0

Expert Reply:

I recommend checking your owners manual for specific torque values for your 2009 Fleetwood Icon Motorhome. If you don't find the lug nut torque specs there, then I've attached a chart for the typical torque specs based on the stud size, wheel size, and wheel material to assist with the general torque values found on most trailers and motorhomes.

expert reply by: Jason S

0

click to enlarge

Answer 1

A 155 indicates 155 millimeters or 6.107 inches wide. A 155/80-12 is not a trailer tire size or at least not common. The closest match is a 145/80-12 such as #AM10130 for a load range D rated for 1,220 pounds at 65 psi. Or #AM10140 rated for 1,520…

view full answer...

Answer 2

The 2-5/16 inch straight tongue couplers are going to fit a 3 inch channel. Your best bet is still removal of the ball on the truck. My recommendation is a whole lot of penetrating oil and a sledge hammer. You won't have to whack it very hard but…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Recommended Torque Specs for Motorhome Lug Nuts

Product Page this Question was Asked From

Continue Researching