Wiring Harness for Prodigy P2 Brake Controller on 2011 Dodge Ram 2500

Question

Question:

I am looking for a wiring harness for my prodigy 2 to fit a 2011 Ram 2500. Which model number harness adapter do I need?

asked by: Rod

0

Expert Reply:

If your 2011 Ram 2500 has either the factory 7 way or factory 4 way, then you will want the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Dodge # 3021-P. The harness is located underneath the dash, to the left of the steering column, taped to another harness near the emergency brake pedal so you will simply plug this custom harness to the factory harness and then the back of your Prodigy P2 # 90885.

expert reply by: Jason S

0

Answer 1

The Prodigy brake controller that I would recommend is the P3 Brake Controller, #90195. This brake controller has an LCD display that will display actual issues rather than codes if an issue were to arise. You can also use the Plug-In Wiring Adapter,…

view full answer...

Answer 2

In order to replace your OEM brake controller with the Tekonsha Prodigy P2 #90885 while using Tekonsha Adapter #3021-P, there are a couple of steps that are required. The picture that you sent of the two plugs are your factory brake controller…

view full answer...

Answer 3

You can bypass the factory brake controller on a 2011 Dodge Ram but there are a few things to do first. I have explained it below and also included a link to an FAQ that will help. To install an aftermarket brake controller on a 2011 Dodge Ram that…

view full answer...

Answer 4

Yes, there is a way to install an aftermarket brake controller on your 2011 Ram 3500 that has an integrated controller in it already. To install an aftermarket brake control you will have to disconnect the ITBM. This will turn on a warning lamp on…

view full answer...

Answer 5

It's possible the brake controller is bad, but you definitely want to check some other things before you purchase a replacement. The first thing to do is inspect both the truck's and the trailer's connectors to make sure the pins are…

view full answer...

Answer 6

I would recommend you start over with your Tekonsha Prodigy P2 Brake Controller #90885 and go through the setup process again so that it will be properly setup. First step is to connect your trailer to your tow vehicle. Next, with the engine running,…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Wiring Harness for Prodigy P2 Brake Controller on 2011 Dodge Ram 2500

Featured Help Information

Miscellaneous Media

Continue Researching