Replacing the Factory Brake Controller on a 2011 Ram 3500 Laramie Longhorn Dually

Question

Question:

What is the best prodigy brake controller for my truck and is there anything I should know about computer flash or special harness. I pull an 11000 5th wheel. Factory controller sucks and dodge wont do anything about it. Want to buy one soon. Thanks.

asked by: Ray

0

Expert Reply:

The Prodigy brake controller that I would recommend is the P3 Brake Controller, # 90195. This brake controller has an LCD display that will display actual issues rather than codes if an issue were to arise. You can also use the Plug-In Wiring Adapter, # 3021-P, to make installation easier.

Your truck will have a brake controller harness under the dash near the steering column. The factory brake controller will be connected to that plug. If you disconnect the factory brake controller, a warning lamp on the dash will turn on. Before disconnecting the factory brake controller, In order to disconnect the ITBM and not get the warning lamp, your local Dodge dealer will have to reconfigure the TIPM (Totally Integrated Power Module), of the truck. Once the TIPM has been reconfigured, and the ITBM has been unplugged, you can use the plug-in harness, # 3021-P, to install the P3 brake control.

To disconnect the ITBM, you will need to contact Business Center to remove the sales code (XHC). The TIPM will need to be reconfigured. Once the sales code has been disabled you can disconnect the ITBM electrical connector, under the dash, without getting the warning lamp.

I have attached the technical bulletin referring to this process for you to check out.

expert reply by: John H

0

Answer 1

If your 2011 Ram 2500 has either the factory 7 way or factory 4 way, then you will want the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Dodge #3021-P. The harness is located underneath the dash, to the left of the steering…

view full answer...

Answer 2

In order to replace your OEM brake controller with the Tekonsha Prodigy P2 #90885 while using Tekonsha Adapter #3021-P, there are a couple of steps that are required. The picture that you sent of the two plugs are your factory brake controller…

view full answer...

Answer 3

You can bypass the factory brake controller on a 2011 Dodge Ram but there are a few things to do first. I have explained it below and also included a link to an FAQ that will help. To install an aftermarket brake controller on a 2011 Dodge Ram that…

view full answer...

Answer 4

Yes, there is a way to install an aftermarket brake controller on your 2011 Ram 3500 that has an integrated controller in it already. To install an aftermarket brake control you will have to disconnect the ITBM. This will turn on a warning lamp on…

view full answer...

Answer 5

It's possible the brake controller is bad, but you definitely want to check some other things before you purchase a replacement. The first thing to do is inspect both the truck's and the trailer's connectors to make sure the pins are…

view full answer...

Answer 6

I would recommend you start over with your Tekonsha Prodigy P2 Brake Controller #90885 and go through the setup process again so that it will be properly setup. First step is to connect your trailer to your tow vehicle. Next, with the engine running,…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Replacing the Factory Brake Controller on a 2011 Ram 3500 Laramie Longhorn Dually

Featured Help Information

Miscellaneous Media

Continue Researching