Length of Mounting Bolts for the Trailer Valet 5X

Question

Question:

How long are the monting bolts?

asked by: Hannah

0

Expert Reply:

The Trailer Valet 5X Swivel Jack, part # STC-V211, has 4 inch long mounting bolts. They're 3/8 inches in diameter as well.

expert reply by: Charles S

0

Answer 1

To help alleviate the back and forth chucking you are experiencing with your 2 inch receiver there are a couple of things I recommend doing. First is to use a cushioned ball mount, the Convert-A-Ball, which is designed to reduce this type of movement…

view full answer...

Answer 2

The #DM5939 is only compatible with the DA91 like the #DM8759131. Unfortunately, there is no option for manual lockout on a DA70 like the ##DM72VR. There are two ways you can keep your brakes from locking up with this brake actuator. The first is to…

view full answer...

Answer 3

You absolutely can! To lock the coupler latch of the Demco Hydraulic Brake Actuator #DM8104311 you were looking at to the hitch ball on your vehicle you will need to use the coupler lock #e98887 which gets inserted into the hole on the latch shown in…

view full answer...

Answer 4

The mounting bracket for the #TV34FR is actually identical to the bracket on the #TV64FR that you were looking at. The holes are 1" apart on center vertically, and 5-1/2" apart horizontally. I have attached a picture for your reference.

view full answer...

Answer 5

We do not offer a jack that swings up and will work with the I-beam aluminum trailer you said you have but we do have a fixed trailer jack that will work for you. I recommend part #HD50000101. This is a fixed mount square tube jack with a 5,000-lb…

view full answer...

Answer 6

The #DM5939 will only work with Demco actuators. As far as I know the Titan Model 6 doesn't have a spot for a lockout key. This means the only option would be to use free backing brakes or add a solenoid like #T4748800

view full answer...

Answer 7

You shouldn't have any problems with the Trailer Valet not staying vertical. If you have a surge brake actuator, like the Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 that doesn't have a reverse lockout, then the only problem that you…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hi Bruce! The Access Toolbox Edition Soft, Roll-Up Tonneau Cover #A63FR will indeed fit your 2021 GMC Serra 1500 SLT with the short bed and your toolbox. This can be used with toolboxes that measure 19" to 21" long, so you are good to go!…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Length of Mounting Bolts for the Trailer Valet 5X

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching