Replacement Roller Assembly Kit Recommendation for Gorilla Lift # GL1

Question

Question:

I NEED ROLLERS PARTS FOR 2 SIDES.DO U HAVE THEM

asked by: WENDELL

0

Expert Reply:

For the Gorilla Lift # GL1 that you mentioned we have the Replacement Roller Assembly Kit # GMNR925 which is the correct replacement rollers.

expert reply by: Jameson C

0

Answer 1

The best trailer tailgate/ramp assist we have for your Bix Tex 70TV Trailer is the Gorilla-Lift Utility Trailer Tailgate Lift Assist part #GL1. That said, this lift assist is only designed for a max side rail height of 24" which is also the max…

view full answer...

Answer 2

There are bolt-on swivel jacks you could change to that would offer similar specs to your current one. The Round Snap Ring Swivel Jack #TJBB-2001-B has a 2,000 lb lift capacity, extended height of 21-1/2" and retracted height of 11". It is…

view full answer...

Answer 3

With the Gorilla Lift Ramp Spring Assist #GL1 there are two sets of springs and you can disconnect the inner spring if you want to lower the spring tension and the outer spring will do the job just fine.

view full answer...

Answer 4

Because the attachment of the cable on the Gorilla Lift, #GL1, to the Spring could be a safety issue, the cable is not available separately. You would need to purchase the Spring and Cable Kit, #GSCC-400, to replace the cable.

view full answer...

Answer 5

The Gorilla Lift #GL1 for trailer tailgates has a 300 lb capacity. For a tailgate that measures 5 foot by 4 foot you should be just fine getting by with just one.

view full answer...

Answer 6

The Replacement Square End Cap #853-5826 should work perfectly for you. I went out and measured one and found that it's overall diameter is 2 inch by 2 inch and the inner tube piece measures a tiny bit over 1.75 inches by 1.75 inches so it would…

view full answer...

Answer 7

Don, it looks like the Gorilla-Lift Utility Trailer Tailgate Lift Assist w/ Cable #GL1 is only going to work with trailers that have a side wall height from 12" to 24" so with yours being so short, it's not going to work unfortunately.…

view full answer...

Answer 8

Since you've already set the first Gorilla-Lift Utility Trailer Tailgate Lift Assist w/ Cable #GL1 to the desired tension to lift the gate alone you may have to redo the placement of your original gate bolt to set the tension correctly for both…

view full answer...

Answer 9

We have installed the Gorilla-Lift Utility Trailer Tailgate Lift Assist #GL1 on similar trailers to your Gorilla 10' trailer with a 2' dovetail. I have included an image below of a similarly designed trailer which has a taller gate. The…

view full answer...

Answer 10

The Gorilla-Lift Utility Trailer Tailgate Lift Assist w/ Cable - 300 lbs #GL1 is a great system that I highly recommend because it utilizes stainless steel cables with sturdy springs to assist each side of the tailgate evenly to prevent warping.…

view full answer...

Answer 11

If you wanted to use the Gorilla-Lift Utility Trailer Tailgate Lift Assist part #GL1 on your utility trailer with tall sides you would need to have a rail that is 12" to 24" from trailer floor. It does not look like there is one from the…

view full answer...

Answer 12

The replacement cable #GLC1-Q1 for the Gorilla Lift tailgate assist #GL1 is the same as the ones that come with the assist so it is stainless steel. For corrosion resistance you can't beat stainless!

view full answer...

Replacement Roller Assembly Kit Recommendation for Gorilla Lift # GL1

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching