Can the Head of the Electric Jack # EJ-3520-BBX be Rotated

Question

Question:

My tailgate comes down on the jack head. Is there a way to rotate the jack head 90 degrees without having to redrill the mounting bolts and rotate it completely

asked by: Barry

0

Expert Reply:

The head of the Electric Jack w/ Footplate # EJ-3520-BBX unfortunately cannot be rotated. Before drilling new holes though I would unbolt the jack and try rotating the whole jack to line up with the same mounting holes and see if that allows your tailgate to come down.

expert reply by: Jon G

0

Answer 1

Hello James, thanks for reaching out. Both the kits you mentioned, the Hydrastar #HYD22FR and #HYD42FR are complete conversion kits for standard 3,500 lb axles. The difference is the calipers included with each kit. The #HYD22FR has stainless steel…

view full answer...

Answer 2

If you're having trouble installing your SnapPads #SP54FR4 then SnapPad actually recommends lifting the jack foot up 3-4" and using a shim to pry the corner of the pad up and help as the jack foot comes back down, sort of like using a shoe…

view full answer...

Answer 3

If you take a look at the diagram I've provided for the Replacement Power Switch for RAM Electric Trailer Jack with Footplate #EJ-3520-PSW which goes to the Electric Jack w/ Footplate #EJ-3520-WBX, you'll be able to see how both of the…

view full answer...

Answer 4

Hi Ken, Happy to help you out here as there is an air bag kit that will fit your 2017 Chevy Silverado 1500 with a 6-1/2' bed and the B&W Turnoverball Underbed Gooseneck Trailer Hitch #BWGNRK1057 installed. What you'll need are air bags…

view full answer...

Answer 5

Hey Joe, yes we have the Air Lift LoadLifter 5000 part #AL57204 that fits your 2016 GMC Sierra 1500 and is also compatible with in-bed hitches like the Curt gooseneck part #C615-632.

view full answer...

Answer 6

Since the Atwood 31013 LP Detector has been discontinued you can replace it with the RV Propane Gas Detector - 12 Volt - 2 Wire - Black #RS44FR. This detector is a surface mount design and can easily swap out your old unit in just a few minutes.

view full answer...

Answer 7

Hi Brenda, The Atwood 31013 unfortunately has been discontinued so you'd need to go with a completely new LP gas detector. We have a couple of surface mount style detectors that come with trim rings that will cover the old unit's cutout hole…

view full answer...

Answer 8

I spoke with my contact at Lippert and he confirmed that the Lippert Components Power Tongue Jack 1817941 #LC285318 can be rotated to be best orientated for you. The jack can be un-bolted, rotated, and reinstalled.

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Can the Head of the Electric Jack # EJ-3520-BBX be Rotated

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching