How to Change Height of Fulton Jack Mounting Bracket

Question

Question:

how do i adjust the height of the mounting bracket? i loosened the bolt behind it

asked by: Arnold

0

Expert Reply:

To adjust the height of the mounting bracket on the Fulton F2, part # F1413040134, you need to loosen the bolt behind the bracket (which it sounds like you have) as well as the bolt in the middle of the bracket. Take a look at video that I have attached for you.

Make sure to tighten both bolts back to spec per the instructions after adjusting the height.

expert reply by: Charles S

0

Answer 1

Yes, the Fulton F2 jack part #F1413060334 that you referenced has a fully extended bracket height of 28-1/2 inches. This dimension is measured from the ground up to the center of the mounting bracket. So it would work great with your trailer frame…

view full answer...

Answer 2

Thanks for the picture, it looks like you have the Fulton F2 Swing-Up, Wide-Track Trailer Jack #F1413040134 in which you'd need the Wide-Track Wheel Assembly for Fulton F2 Adjustable A-Frame Jack #F500266 for a replacement.

view full answer...

Answer 3

Hi Louis; the Fulton F2 Boat Trailer Jack w Wide-Track Wheel #F1413140334 has the same swivel mount height adjustability found on the #F1413040134. This can be seen in the instructions linked below. We are currently waiting for stock from Fulton. As…

view full answer...

Answer 4

The 'sleeve' or shank portion of the Fulton #F500266 caster assembly is meant to be compatible with Fulton F2 trailer jacks, which is why it's kind of oddly shaped. At the widest point, that sleeve is 2-1/2 inches in diameter, as shown in…

view full answer...

Answer 5

That definately seems like an excessive amount of play in your Fulton F2 Swing-Up Trailer Jack #F1413140334. As these jacks have a lifetime warranty you can reach out to Fulton to see if they would either send you a new Wheel Assembly #F500266 or an…

view full answer...

Answer 6

The Fulton F2 Swing-Up Trailer Jack #F1413040134 referenced in your question features a lubricated 1-piece gearbox that reduces the need for period manual lubrication but you can certainly add extra grease when needed using the ventilation port. You…

view full answer...

Answer 7

There may have been an older version of the Fulton trailer jack #F1413100334 that you referenced that required adding a grease fitting but this jack does not require that. It would work well for you and not require any greasing or maintenance.

view full answer...

Answer 8

The Fulton F2 Swing-Up Trailer Jack #F1413040134 (as well as other F2 jacks) has that plastic piece that as you referenced is #9 in the exploded diagram. I reached out to my tech contact at Fulton and unfortunately that is not a replaceable part. You…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

How to Change Height of Fulton Jack Mounting Bracket

Featured Help Information

Miscellaneous Media

Continue Researching