Timbren Suspension Kit Recommendation for 2015 Ford F-350

Question

Question:

What is the recommended Timbren kit for the rear of a 2015 F-350 CCSB SRW?

asked by: Dave

0

Expert Reply:

For your 2015 Ford F-350 crew cab short bed single rear wheel the Timbren kit part # TFR350SDF is a confirmed fit and will work great. This kit can provide up to an additional 8,600 lb of suspension support and fits versions of your truck that have and do not have the overload springs.

expert reply by: Jameson C

0

Answer 1

The difference in harshness between the Timbren kits part #TFR350SDF and #TFRTT350F would be very noticeable. Especially when unloaded. Your truck is already going to have a rough ride as that is the nature of 1 ton trucks but the 12k Timbren kit…

view full answer...

Answer 2

That's a good question, and between the two systems, the best one for your 2008 Ford F-350 for support while you are towing your 5th wheel as well as when you using a truck camper is the 8,600 lb option: - Timbren Rear Suspension Enhancement…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

Hey David, it sounds like you know what you're doing but I've also gone ahead and found the wiring diagram for the Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR for you to check out so you can use it as a cross…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

Hello Matt, I was seeing some mixed information on this as well, so I reached out directly to my contact at Firestone to confirm. The Firestone Ride-Rite Air Bags w/ Easy Mount Compressor - Wireless Control - Single Path - 5,000 lbs #F44XV will fit…

view full answer...

Timbren Suspension Kit Recommendation for 2015 Ford F-350

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching