Repair Kit for Lippert LCI PN241846 Lead Leg on Landing Gear System

Question

Question:

Hi, I am looking for a leg repair kit for a Lippert front landing gear, each leg has its own motor so the kit would be for a lead leg. The part number I have off of the leg is LCI PN241846. The main tube is 29.5 inches long and 2.5 by 2.5 inches square. Thanks

asked by: Dave L

1

Helpful Expert Reply:

The Lippert Landing Gear Leg model LCI PN241846 on your landing gear system refers to the Lippert Heavy Duty Landing Gear Master Leg # LC241846. For a repair kit that will work nicely with this leg, you can use the Lippert Lead Leg Repair Kit # LC146059.

This kit includes 1 lead drive shaft, 2 drive shaft bushings, 1 E-Clip, 1 drive pin, 1 spiral pin, 1 12T bevel gear, 1 16T bevel gear, and 1 shim washer.

expert reply by: Chris R

1

Answer 1

Repair kit #LG-146059 contains 2 pins and the drive shaft all of which are for the top of the jack. To help I have included the written instructions below and also a diagram that points out the parts mentioned in the written instructions. The…

view full answer...

Answer 2

The 241845 actually comes back to the Replacement Heavy-Duty Landing Gear Jack Leg #LC241845 which is the replacement leg for the Ground Control 2.0 which does not have a gear repair kit available so you would need to replace the leg with a new…

view full answer...

Answer 3

I believe you are asking about the weld stops on the Replacement Heavy Duty Landing Gear Master Leg #LC241846. As shown in the attached diagram, the distance from the top of the upper weld stop to the bottom of the lower one on #LC241846 is 17.5…

view full answer...

Answer 4

You are correct that the Reese Electric 5th Wheel Landing Gear Set - 8,000 lbs #RP500708 should drop right into place where your Lippert Venture landing gear was. These will support 4,000 lbs each, which is definitely enough capacity for your…

view full answer...

Answer 5

Hey Tom, the Replacement Heavy Duty Driver Leg part #LC241846 that you referenced is a lead screw type as it does not have any bearings.

view full answer...

Answer 6

The correct landing gear leg replacement for the Lippert Ground Control 2.0 that you have is actually the part #LC241846. We have no way of knowing if the #LG-179013 could work for you since it's never been tested although I can see how it looks…

view full answer...

Answer 7

The difference is the height; the Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg #LC179013 and Replacement Lead Jack w/ Drop Leg for Stromberg Carlson Landing Gear - 29-1/2" #LG-179013 is the lengths. The Stromberg-Carlson…

view full answer...

Answer 8

You'll need a new jack leg based on what you described. For a replacement you'd want the part #LC241845 for the driver side or part #LC241846 for the lead leg that is normally on the passenger side.

view full answer...

Answer 9

For the driver leg part #LC241846 that you have the correct repair kit you'll want is the #LC146059.

view full answer...

Answer 10

I have attached for you a set of photos which are used to identify the landing gear legs on a trailer. I assume you have either the older Lippert Ground Control 2.0 Leveling System or the newer Lippert Ground Control 3.0 Leveling System. If that is…

view full answer...

Answer 11

If you have the Lippert Ground Control 2.0 Electric Leveling System on the Crusader 5th Wheel then you'll need the Replacement Heavy-Duty Landing Gear Jack Leg for Ground Control 2.0 part #LC241846 for 29-1/2" outer tube or part #LC241845…

view full answer...

Answer 12

I attached a diagram that shows how the Lippert Components Venture Lead Leg Repair Kit #LG-146059 installs.

view full answer...

Repair Kit for Lippert LCI PN241846 Lead Leg on Landing Gear System

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching