Air tank and Compressor Installation in Truck Bed

Question

Question:

Can I mount the compressor and tank in the bed of my truck? It has a cover over my bed.

asked by: Mark D

0

Expert Reply:

The Air Lift QuickShot Compressor System for Air Springs - Support Line and Reserve Tank # AL25690 can absolutely be mounted in the bed of your truck if desired. The cover over your bed whether a tonneau cover or a camper shell will keep the elements out of the system so that installation will work very well. The only parameters for installation are in the attached installation details that your mounting location will not have any issue with.

expert reply by: Jason S

0

Answer 1

Hey Steve, welcome back! The difference between these two Hellwig Adjustable Big Wig Rear Anti-Sway Bars is the fitment. The #HE94FR is designed for 4WD models and the #HE97MR is designed for 2WD models. Since your 2019 F-250 is 4WD you need the…

view full answer...

Answer 2

You will need to switch the single path gauge on system #AL25690 to a dual-path gauge to be able to control each air bag individually. You can use Firestone kit #F2145. It comes with the gauge, additional hose, fittings, and wiring plus accessories.…

view full answer...

Answer 3

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

Hello Matt, I was seeing some mixed information on this as well, so I reached out directly to my contact at Firestone to confirm. The Firestone Ride-Rite Air Bags w/ Easy Mount Compressor - Wireless Control - Single Path - 5,000 lbs #F44XV will fit…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Hi Bill! Thanks for your pictures, they were extremely helpful! ^___^ The LCI Part #194170 on that tag you found means you have a 1621 pin box. The Gen-Y #GY45SR you were looking at is specifically for the Lippert 1116 and 1716 pin boxes, so you will…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Air tank and Compressor Installation in Truck Bed

Continue Researching