Will 7-Piece Installation Set for Bearings, Races, and Seals Work With Bearing L44649?

Question

Question:

Hello, I am curious if L44649 bearings are compatible with this tool. Thanks!

asked by: Nathan S

0

Expert Reply:

Yes, the 7-Piece Installation Set for Bearings, Races, and Seals # PTW83020 is compatible to use with Bearing # L44649.

expert reply by: Kyle S

0

Answer 1

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 2

To add grease to the Dexter Trailer Hub and Drum Assembly for 3,500-lb E-Z Lube Axles #84546UC3-EZ I recommend using the LubriMatic Prime Guard High Temperature Wheel Bearing Grease #L11380. This is the same type of grease used in our pre-greased…

view full answer...

Answer 3

Yes, it does. The Dexter Trailer Hub & Drum Assembly for 3,500-lb Axles item #84546UC3-EZ comes ready to be installed. The bearings, races, and grease seal are all preinstalled, greased, and ready to go.

view full answer...

Answer 4

You do not need to add additional grease to a Dexter trailer axle hub that came pre-greased. It has the correct amount in it and is ready to be used. Adding additional grease will most likely blow out the grease seal.

view full answer...

Answer 5

Hey Ed, The Easy Grease Trailer Hub/Drum Assembly #AKHD-545-35-G-EZ-K uses grease seal #58846 and are made by AxleTek, who is not in the U.S. The Dexter Trailer Hub & Drum Assembly #84546UC3-EZ and #84546UC3 uses the same grease seal part number,…

view full answer...

Answer 6

The Bearing Kit #BK2-100 should contain all the correct bearing, seals and races for 1 wheel. I always recommend pulling one hub apart and confirming the correct spindle. These fit the most commonly used axles under your 2014 Forest River R-Pod 179…

view full answer...

Answer 7

A wider wheel would allow the tire to have a flatter surface across the top of it when inflated which might help a little bit with tire wear but realistically that difference is very miniscule. With the Karrier ST205/75R14 Radial Trailer Tire - Load…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Will 7-Piece Installation Set for Bearings, Races, and Seals Work With Bearing L44649?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching