Thickness of Curt Ball Mount # C45030 Platform

Question

Question:

I would like to know the thickness of the ball mount platform. Thanks

asked by: Mike M

0

Expert Reply:

The ball mount platform of the Curt ball mount part # C45030 that you referenced is 3/4 inches thick.

expert reply by: Jameson C

0

Answer 1

The height of the Curt Reducer Bushing for Ball Mounts, part #C21100 is .551 inches. This is the only size we have for this application.

view full answer...

Answer 2

We currently carry four different size hitch balls which are 1-7/8", 50mm, 2", and 2-5/16". The most common hitch ball size in Europe is 50mm for which you can use part #63912 if you need a 3/4" diameter shank or part #EH53C-C if…

view full answer...

Answer 3

I have two options for you to consider The Curt ball mount #C45220 will have a 2-3/8 inch drop and ball hole diameter of 1-inch. It's the closest to the 3-inch drop you referenced but currently there isn't any with a 3-inch drop only. The…

view full answer...

Answer 4

We have one standard 50 mm hitch ball that you could use with the Brophy part #EH53C-C but the one you mentioned wouldn't be ideal as the bottom portion of the ball is cut flat like you noticed. The 50 mm size is pretty rare here in the US which…

view full answer...

Answer 5

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 6

I have a solution but the Weigh Safe 180 Hitch 2-Ball Mount #WS54FR will not work with this because most European Bike Racks require a 50mm ball to attach to. The two included balls with Weigh Safe ball mount are not the correct size. Also, this ball…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Matt, welcome back! You are correct. The threaded hole on the Weigh Safe 180 Hitch 2-Ball Mount for 3" Hitch item #WS34MR ball retainer, is to make removing the pin easier. You can insert a 1/4"-20 screw to get additional leverage to…

view full answer...

Thickness of Curt Ball Mount # C45030 Platform

Product Page this Question was Asked From

Continue Researching