Comparing EZ-Lube Spindles to Bearing Buddy Grease Caps
Updated 04/03/2018 | Published 04/01/2018 >
Products Featured in This Question
Question:
My boat trailer has grease caps with rubber plugs. Remove plug to get to zerk type. If i go with a bearing buddy typezerk on outside would I remove the inside zerk to allow the grease to move through. Or am I over thinking the solution?
asked by: David
Expert Reply:
It sounds like you have EZ-Lube spindles like # TRU74FR and special EZ-Lube grease caps like # RG04-040 on your boat trailer. Since you already have a handy method to top off your hubs' grease level there is really no need to move to Bearing Buddy grease caps. Both methods provide a good means to ensure the proper grease level but only one of the two is needed.
If you really want to switch from EZ-Lube spindles to Bearing Buddy grease caps you could do this, strictly speaking, but you would not really gain anything. It would be necessary to unscrew the zerk fittings so that the grease that is pressurized by the Bearing Buddy could work its way into the bearings.
Product Page this Question was Asked From
#84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter
- Trailer Spindles
- EZ Lube Spindle
- With Flange
- L68149
- 1-3/4 Inch Diameter
- Round
- For 3500 lb Axle
- TruRyde
more information >
Continue Researching
- Shop: DeeMaxx 10" Hub/Rotor Assembly - 5 on 4-1/2 - Maxx Coating - 3,500 lbs
- Shop: Dexter 10" Hub-and-Rotor Assembly - 5 on 4-1/2 - Zinc - 3,500 lbs
- Shop: Timken Bearing Kit for 3,500 lb Axles with #84 Spindle - Bearings L44649/L68149
- Search Results: square axle
- Search Results: trailer axles
- Search Results: square axle ~ 1~1/2 inch trailer suspension parts
- Video: All You Need to Know About the Grease Cap, 1.99" OD EZ Lube Drive in with Plug
- Shop: Trailer Axle Beam with Easy Grease Spindles - 95" Long - 3,500 lbs
- Q&A: Greasing EZ Lube Spindles When Grease Comes Out Cotter Pin Hole
- Q&A: Do Grease Zerks Need to be Removed to Use Bearing Buddies
- Q&A: Does Installation of Bearing Buddy Require Removal of Zerk Fitting
- Shop: Bearing Buddy Bearing Protectors - Model 2240SS - Stainless Steel - Qty 2
- Shop: Grease Cap, 1.99" OD EZ Lube Drive in with Plug - Qty 2
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer tires and wheels
- Shop: Trailer Wiring
- Search Results: trailer wiring
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Q&A: Comparing Kenda KR03, KR35, And KR53 Tires
- Shop: Suspension Enhancement
- Shop: Brake Controller
- Search Results: trailer jack
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)

