Least Visible Trailer Hitch Recommendation for 2017 Toyota Sienna
Updated 06/18/2020 | Published 02/28/2018
Question:
I have a new 2017 Toyota Sienna SE, I would like to put a trailer hitch on. The Curt 13105 looks relatively easy to install, especially with your video. But, I would rather use the Curt C13343 for a more custom look. I have watched the C13105 video and it makes complete sense, but the written instructions for the C13343 have you taking off the back facia. The underpanel makes sense, but I cant see any reason to take off the rear facia. it uses the same bolt holes as the C13105. It is up behind the rear facia, but nothing seems to be in the way. Can the C11343 be installed without pulling off the rear facia. My van has 50 miles on it and I a little itchy about removing exterior visible body parts. Is there an installation video for the C13343. Thanks for your help.
asked by: Brian B
Expert Reply:
Of the 2 inch Curt hitches we offer for your 2017 Toyota Sienna the part # C13343 is the one to go with as it has only the hitch opening visible down below the bumper.
The instructions do recommend removing the rear fascia to install the hitch. We sometimes find that there can be shortcuts made to install hitches but in general that is not the case. We currently don't have an install video for this hitch yet either.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 525 lbs TW
- 3500 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: Brake Controller
- Shop: Trailer Wiring
- Search Results: adjustable ball mount trailer hitch ball mount
- Search Results: brake controller
- Search Results: 60732
- Search Results: trailer hitch ball mount
- Search Results: tekonsha
- Search Results: 118648
- Search Results: towsmart
- Q&A: Rear Suspension Enhancement and Trailer Wiring for 2020 RAV4 LE
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Video: Upgraded Custom Trailer Wiring Available On Your 2017 Toyota Sienna
- Q&A: Recommended Trailer Hitch for 2020 Toyota Sienna for Ground Clearance
- Q&A: Hitch, Weight Distribution and Brake Controller Recommendations for a 2017 Toyota Sienna XLE
- Article: My Trailer Hitch Doesn't Fit
- Shop: Vehicle Air Mattress
- Article: The 5 Best Trailer Drop Hitches You Can Buy
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness - Dash Knob - Proportional
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Article: Holiday 2025 | RVers’ Favorite Gear & Road Picks
- Shop: Floor Mats
- Q&A: Concealed Trailer Hitch With Maximum Ground Clearance/Trailer Wiring Harness for 2020 Toyota Sienna
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Article: Stability Control for Heavy Duty Vehicles
- Q&A: Does Draw Tite or Curt Hitch for 2017 Toyota Sienna have Best Ground Clearance
- Shop: Air Lift 1000 Air Helper Springs for Coil Springs - Rear
on Trailer Hitch
B H.
6/14/2020
I am having trouble getting the 5th and 6th screws in (the two closest to the engine on driver and passenger side. It seems out of tolerance where the hitch hole is not aligned with screw insert, so the screw cannot be inserted. Anyone else have this problem?