Reese Weight Distribution Shank # RP54977 Work with all Reese Weight Distribution Systems

Question

Question:

Can I use the titan RP54977 with the same head that is attached to my RP54970

asked by: Bob F

0

Expert Reply:

The Reese shank part # RP54977 fits quite a few Reese weight distribution systems but it does not fit any styles of WD system that use washers for head angle adjustment. So as long as yours does not use washers you'd be fine.

expert reply by: Jameson C

0

Answer 1

We do have weight distribution shanks available that are designed to fit 2-1/2 inch hitch receivers like what is on your Silverado 2500. For the Reese Steadi-Flex Weight Distribution System #RP66561 that you were looking at, you will just need to add…

view full answer...

Answer 2

Hi Jordan! You are absolutely correct. The Equal-i-zer Weight Dist Shank - 2-1/2" Hitch - 8" Rise, 4" Drop #EQ90-02-4800 will work with your Reese weight distribution system, but you will need to adjust it a little due to the different…

view full answer...

Answer 3

Generally speaking a reducer sleeve does not decrease the capacity of a trailer hitch but this can depend a bit on the particular trailer hitch or the reducer sleeve being used. We have seen, such as in your case, that certain sleeve manufacturers do…

view full answer...

Answer 4

There are a few different options for a replacement shank since the 54977 has been discontinued. You can use the Equal-i-zer #EQ90-02-4900 with a 10" rise/6" drop or #EQ90-02-4800 with an 8" rise/4" drop. You will need to choose…

view full answer...

Answer 5

Hey Paul, the most similar weight distribution shank we have to the part #RP69FR that fits a 2-1/2 inch hitch is the part #BPH75RR which fits the same heads as the Reese shanks so it will also work with same heads.

view full answer...

Answer 6

I suggest using the Reese Titan Shank #RP54977 with the Reese Stait-Line #RP66130. It provides up to 5-3/4 inches of drop or 8-1/4 inches of rise and fit your 2-1/2 inch receiver. Also for a hitch ball you can use #C40030.

view full answer...

Answer 7

Reese Titan Weight Distribution Shank #RP54977 is compatible with the 2-1/2 Class V receiver opening on your 2015 Ford F-350. It is also compatible with the Reese Strait-Line, dual-cam sway control system that you have. I have linked a video review…

view full answer...

Answer 8

Either hitch pin hole of the B&W Tow and Stow Ball Mount part #BWTS10049B can be used in the hitch of your vehicle. Whichever one works for your towing application best will be perfectly fine.

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Reese Weight Distribution Shank # RP54977 Work with all Reese Weight Distribution Systems

Continue Researching