Is There Reese Weight Distribution Shank that Fits 2-1/2 inch Hitch Size

Question

Question:

Does the 3357 shank come in 2.5 inch

asked by: Paul

0

Expert Reply:

Hey Paul, the most similar weight distribution shank we have to the part # RP69FR that fits a 2-1/2 inch hitch is the part # BPH75RR which fits the same heads as the Reese shanks so it will also work with same heads.

expert reply by: Jameson C

0

Answer 1

First, when calculating tongue weight, after you have the tongue weight of the trailer, loaded and ready to tow, you then have to add to that the weight of anything you are carrying behind the rear axle of the tow vehicle. If you have 200 pounds of…

view full answer...

Answer 2

Hey Tyler, so the difference is the amount of motors that each has. The Lippert PSX2 has two and the Lippert PSX1 like the part #LC298707 has a single motor. The foot print and mounting etc. is exact same so this will fit and work great in place of…

view full answer...

Answer 3

Most WD shanks that fit a 2-1/2" receiver taper down to the normal 2" receiver size, just like the Equal-i-zer Shank #EQ90-02-4700. The only thing that you need to be sure of is that the mounting holes are in the same space. I have linked a…

view full answer...

Answer 4

Hi Joe, I assume you are referencing an Equal-i-zer weight distribution since you have shank #EQ90-02-4700. I went ahead and read the owners manual for their systems and there is noting regarding adjusting the angle of the hitch ball. The hitch head…

view full answer...

Answer 5

I recommend adding a shank with a taller rise. The Equal-i-zer Weight Distribution Shank item #EQ90-02-4300 has a 10 inch rise. This shank has a 600 to 1,400 lbs tongue weight and is compatible with Reese weight distribution systems.

view full answer...

Answer 6

When choosing a weight distribution system, you want to go off the total tongue weight. This total tongue weight includes the loaded weight of the trailer tongue that you stated along with any cargo behind the rear axle of the towing vehicle. For the…

view full answer...

Answer 7

There is a solution for you to use a weight distribution system with your motor home. I recommend you use a system with chain hangers such as the Reese Strait-Line #RP66074, as height will not be an issue. Width still matters though, and the…

view full answer...

Answer 8

I pulled one of the Curt Hitch Balls, part #C40087 from our warehouse and took a couple of measurements for you. I have attached a photo of the hitch ball with the dimensions noted. As the photo shows, the 2 inches is measured from the top of the…

view full answer...

Answer 9

Reese Titan Weight Distribution Shank #RP54977 is compatible with the 2-1/2 Class V receiver opening on your 2015 Ford F-350. It is also compatible with the Reese Strait-Line, dual-cam sway control system that you have. I have linked a video review…

view full answer...

Answer 10

We do have weight distribution shanks available that are designed to fit 2-1/2 inch hitch receivers like what is on your Silverado 2500. For the Reese Steadi-Flex Weight Distribution System #RP66561 that you were looking at, you will just need to add…

view full answer...

Answer 11

It sounds like you just need to adjust the camera on the Furrion RV Observation Camera System part #FOS43TASF. The camera can be tilted up and down but not side to side. If you place a firm grip on the camera housing you can then tilt the camera up…

view full answer...

Answer 12

Hey Greg, you could go with the Curt Class V hitch part #C15802 to replace your worn out hitch. Then for a 2-1/2 inch shank to use with your WD system you could us the Equal-i-zer Shank part #EQ90-02-4900.

view full answer...

Is There Reese Weight Distribution Shank that Fits 2-1/2 inch Hitch Size

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching