Replacement Hitch Bolt for Yakima HoldUp 1-1/4 Inch Bike Rack # Y02445

Question

Question:

What threaded hitch bolt would I need for this

asked by: Jamie S

0

Expert Reply:

You will need Replacement Mounting Hardware # Y8890176 to go with Replacement 1-1/4" Tongue for Yakima HoldUp Bike Racks # 8880581.

expert reply by: Michael H

0

Answer 1

There is definitely a way to lock your Yakima bike rack to your hitch. The Yakima HitchLock #Y07235 is designed to fit both 1 1/4" and 2" hitch pins and will get you all squared away. However, if there are already locks on your bike rack…

view full answer...

Answer 2

I spoke with my contact at Yakima regarding the Replacement 1-1/4 Inch Tongue for Yakima HoldUp Bike Racks #8880581 referenced in your question. She stated that the only additional hardware that will be needed to install the tongue is the existing…

view full answer...

Answer 3

The Yakima Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier, part #Y8890200, is a 5/8 inch bolt. The size wrench you would use to install or remove this bolt is 15/16 inch.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

Hello Kevin, thanks for reaching out. Yakima does confirm the Timberline towers to fit the factory raised rails on the 2025 Honda Pilot. Sadly, they do not offer a direct fit for the LockNLoad Platform so your best option would be to go with a roof…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Replacement Hitch Bolt for Yakima HoldUp 1-1/4 Inch Bike Rack # Y02445

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching