What Are The Measurements Of The Yakima Hitch Pin #Y8880129?

Question

Question:

Ive got a 4-bike fold-down Yakima hitch rack probably made sometime around 2000-2003, for a 1-1/4inch receiver. I cant find any sort of model number on it. I want to make sure this matches the rack, and cant find diameter listed. Thanks

asked by: Jase

0

Expert Reply:

The Replacement Mounting Hardware for Yakima HoldUp Hitch Mounted Bike Carrier - 1-1/4" Hitches # Y8880129 is a 1/2 inch diameter with a thread pitch of 13 (threads per inch). It is 4.28 inches long. I contacted the manufacturer to get their official measurements for this part.

expert reply by: Jason S

0

Answer 1

Replacement Threaded hitch pin #Y8880129 is indeed longer than the original bolt. It is 4.28 inches long overall. Something that you should know though is that when using a hitch adapter like you mentioned it reduces the tongue weight capacity of the…

view full answer...

Answer 2

The Yakima Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier, part #Y8890200, is a 5/8 inch bolt. The size wrench you would use to install or remove this bolt is 15/16 inch.

view full answer...

Answer 3

We do carry replacement end caps for the Yakima HoldUp Bike Carrier. For an original HoldUp carrier you can order part #8880222. The other end cap we offer, part #8880228, will fit all HoldUp bike carriers and is designed for use with the bike…

view full answer...

Answer 4

You will need the Yakima Replacement Spine Assembly for 2 inch HoldUp Bike Racks, item #8890277, to replace the shank on your 1-1/4 inch HoldUp rack and make it work correctly in your 2 inch hitch.

view full answer...

Answer 5

I definitely have some options so that you can use your Yakima Hold-Up EVO Bike rack #Y02480, but the reason Yakima does not recommend using an adapter with this bike rack is because most hitch adapters reduce the weight capacity of your hitch by…

view full answer...

Answer 6

In order to convert your Yakima HoldUp #Y02445 to be compatible with a 2 inch hitch, you would only need the Replacement Tongue for Yakima HoldUp Bike Racks #8880580, which is a 2 inch tongue.

view full answer...

Answer 7

You will need Replacement Mounting Hardware #Y8890176 to go with Replacement 1-1/4" Tongue for Yakima HoldUp Bike Racks #8880581.

view full answer...

Answer 8

The hitch bolt included in the Yakima Replacement Mounting Hardware for SwingDaddy Hitch Mounted Carrier #Y8890185 measures exactly 4.28 inches long with a 1/2 inch diameter and 13 pitch. If you only need the bolt and clip you can use part…

view full answer...

Answer 9

My technical contact at Softride explained to me that the reason the Hitch Rack Lock SR25056 is only 1/2 a bolt is because the other side of the Softride bike racks have a smaller hole so a full bolt cannot pass all the way through. He did tell me…

view full answer...

Answer 10

Threaded hitch pins are usually brand-specific and match the threads in the shank portion of an accessory item like a bike rack, for example. We have 16 different threaded-bolt locks for 2-inch hitches, shown on the linked page. Thule offers a…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

What Are The Measurements Of The Yakima Hitch Pin #Y8880129?

Continue Researching