Weight Distribution System With Empty Trailer
Published 02/09/2018 >
Question:
I was looking at an Equal-I-zer hitch for my 24foot enclosed trailer Ive been watching different videos and reading and I havent seen anyone ask the question where to set the hitch for an enclosed trailer. My trailer is setup for camping and we go to swap meets so if I pack it up and go for the weekend on the return trip it will be less weight do I need to readjust the hitch? I dont know that Ill have access to a perfectly level spot to do so, and that seems like a lot of added time to the trip. Is it necessary to adjust for an empty trailer? Thanks!
asked by: Ben A
Expert Reply:
Weight distribution systems have a total tongue weight rating range. When you use weight distribution, you need to account for the loaded tongue weight of your trailer along with any cargo behind the rear axle of your towing vehicle. Ideally, you want to be in the middle of this range when loaded.
When unloaded, it is ideal to fall within that range as well, but that isn't always possible. With a 24 foot enclosed trailer, you most likely will still have enough tongue weight to utilize your system when unloaded, but you do have the option of removing the system if it provides too rough a ride when unloaded.
For instance the Equal-I-zer # EQ37100ET has a total tongue weight range between 600 and 1000 lbs. So you may have a loaded weight around 900 lbs and an unloaded weight around 650 and it would still utilize this system well for sway control and stability. If the tongue weight were to drop to 450 when empty, it may be wise to remove the system.
If you have more specific numbers, I can give you a recommendation for your system.
Product Page this Question was Asked From
Equal-i-zer Weight Distribution System w/ 4-Point Sway Control - 10,000 lbs GTW, 1,000 lbs TW
- Weight Distribution Hitch
- WD With Sway Control
- Trunnion Bar
- Fits 3 Inch Frame
- Fits 4 Inch Frame
- Fits 5 Inch Frame
- Fits 6 Inch Frame
- Includes Shank
- 2-5/16 Inch Ball
- Fits 2 Inch Hitch
- Allows Backing Up
- 700 lbs
- 800 lbs
- 900 lbs
- Equal-i-zer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Weigh Safe True Tow Weight Distribution Hitch - 2" Shank - 6" Drop - 12.5K GTW, 1.2K TW
- Shop: Curt Short-Arm Weight Distribution System with Shank - Trunnion Bar - 10,000 lbs GTW, 1,000 lbs TW
- Shop: Curt MV Weight Distribution System - Round Bar - 8,000 lbs GTW, 800 lbs TW
- Video: DIY Install: Curt MV Weight Distribution System on your 2003 Ford F-250 and F-350 Super Duty
- Shop: Loadstar ST205/75D15 Bias Trailer Tire - Load Range C
- Article: 2 Steps for Finding the Right Weight Distribution Hitch Size
- Article: 5 Things to Know About Weight Distribution Hitches
- Video: Customer Review - Curt MV Weight Distribution System
- Q&A: Why Can't You Back Up with Curt Weight Distribution System Installed
- Q&A: Can You Back Up a Trailer when Using Weight Distribution
- Q&A: Weight Distribution Recommendation for 6700 lb Trailer
- Q&A: Trailer Hitch Ball Wrench Size and Torque Rating for 1-1/4 Inch Hitch Ball Shank Size
- Search Results: anti~sway bars
- Search Results: trailer sway control
- Shop: Curt MV Weight Distribution System - Round Bar - 14,000 lbs GTW, 1,400 lbs TW
- Shop: Curt TruTrack Weight Distribution System w/ Sway Control - Trunnion - 10,000 lbs GTW, 1,000 lbs TW
- Shop: Fastway e2 Weight Distribution w/ Sway Control - No Shank - Round - 10,000 lbs GTW. 1,000 lbs TW
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer tires and wheels
- Shop: Trailer Wiring
- Video: How to Choose a Trailer Brake Controller
- Q&A: Is The Equal-i-zer Weight Dist Shank EQ90-02-4100 For A 2" or 2.5" Hitch?
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer wiring
- Shop: Suspension Enhancement
- Shop: Brake Controller


