Retracted Bracket Height for Jet Powered A-Frame Jack part # JET-3755

Question

Question:

What is the distance from the bottom of the mount plate to the bottom of the when fully retracted. Thank you.

asked by: Bill

1

Helpful Expert Reply:

The retracted bracket height that you are looking for on the Jet powered jack part # JET-3755 is 8-1/2 inches. That's the distance from the bottom of the mounting flange to the bottom of the foot when fully retracted.

expert reply by: Jameson C

1

Answer 1

The Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 24" Lift - 3,500 lbs #JET-3755 (Black) and #JET-3555 (White) both measure 23 inches from the mounting plate to the top of the jack. I have added links to some video reviews for…

view full answer...

Answer 2

For your 7x14 foot enclosed trailer, I recommend the Stromberg Carlson Electric Trailer Jack #JET-3755. This jack has a lift of up to 24 inches, has a drop leg for faster extension and retraction, and has a motor rated higher then your trailer tongue…

view full answer...

Answer 3

I recommend looking at the Stromberg Carlson Electric Trailer Jack #JET-3755. This is a very nice electric jack that has a lift capacity of 5,000 pounds, which is more than enough for your 10,000 pound travel trailer. Going with a jack with a…

view full answer...

Answer 4

The Stromberg Carlson #JET-2500 Electric Trailer Jack you referenced has a lift capacity of 2500 lbs. The jack will work just great for trailers with tongue weights less than 2500 lbs, the tongue weight of your Coachmen Cascade should certainly be…

view full answer...

Answer 5

Yes! The Stromberg Carlson Electric Trailer Jack #JET-3755 is compatible with the Lippert #LC429756 that you referenced and it does measure the 8-1/2" when retracted. You could potentially use a caster wheel like part #PS1400750340 but this…

view full answer...

Answer 6

One way to determine the lift and jack height you need would be to measure the jack you currently have on your 2018 Intech Luna RV. If this is not possible, or you still aren't sure, you can also determine the correct jack using the coupler…

view full answer...

Answer 7

On the Stromberg-Carlson powered A-frame trailer jack, #JET-2500, it is approximately 27 inches from the mounting bracket to the top of the jack.

view full answer...

Answer 8

The correct electric A-Frame trailer tongue jack for your 12,500-lb triple axle travel trailer will need to have the capacity that will surpass your trailer's loaded tongue weight, which is typically between 10 and 15 percent of the loaded…

view full answer...

Answer 9

We have many jack covers that you could use but none specifically for your Lippert jack. Ultra-Fab cover #UF38-944020 is 12" x 14-1/2". Ultra-Fab also has #UF38-944026 which is 14-1/2" x 15-1/2". Cover #JET-01 is designed for…

view full answer...

Answer 10

Yes, the a-frame jack mounting holes are concentric therefore you can rotate an a-frame tongue jack such as the Stromberg Carlson Electric Trailer Jack part #JET-3755.

view full answer...

Answer 11

I have provided a picture that shows the jack dimensions. These measurements were taken here by another Expert recently. The outer tube is 2 inches in diameter and the inner tube is 1-3/4 inches in diameter. The bracket to mount the jack uses a…

view full answer...

Answer 12

Yes, the vast majority of a-frame trailer jacks use the same bolt pattern which is 3" apart on center. Therefore you should have no problems whatsoever using an electric a-frame trailer jack on your T@B 320 S teardrop camper. For this, I…

view full answer...

Retracted Bracket Height for Jet Powered A-Frame Jack part # JET-3755

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching