Location Of Factory Brake Controller Port On 2007 Toyota Tundra SR5 w/ Tow Package

Question

Question:

I have a 2007 Tundra SR5 4.7L with tow package but I cannot find the coonnector on the truck to plug the haress into. I assumed it was under the kick panel but I did not find it. Where is it?

asked by: Jim D

0

Expert Reply:

The connector should be located underneath the dash to the left of the steering column. It may be taped to another wire and tucked up and out of the way.

I have linked a video installation of brake controller being installed on a 2007 Toyota Tundra using the # 3040-P adapter.

expert reply by: Reno H

0

Answer 1

We can definitely help install a brake controller and 7-way on your 2024 Toyota Grand Highlander but first the brake controller I recommend is the Redarc Tow Pro Liberty part #RED24FR with the install harness part #RED69FR. As this controller puts…

view full answer...

Answer 2

The factory harness to plug in a brake controller wiring harness on your 2007 Toyota Tacoma is located underneath and left of the steering column, taped to another harness near the emergency brake pedal. There will be a 5-pin connector that mates…

view full answer...

Answer 3

Most likely the colors would match with the exception of the red wire on the trailer going to the white wire on the truck. The white wire is the ground circuit so you can trace the RED wire on the TRAILER to see if it attaches to a metal surface on…

view full answer...

Answer 4

Going by the colors that you mentioned, it sounds like you have the typical set-up, green wire for right turn and brake, white wire for ground, yellow wire for left turn and brake, brown with green wire for right side running lights, and brown with…

view full answer...

Answer 5

Your Hydrastar actuator is not cycling on to build pressure to apply the brakes when needed. This could mean that there is an electrical problem or a malfunction with the motor, or even a problem with the brake controller. I have included a picture…

view full answer...

Answer 6

The Hopkins #HM11143395 you've looked at is the correct replacement 7-way for your 2007 Toyota Tundra. The installation is pretty simple, you can see the procedure by clicking the provided link and viewing the video showing the harness being…

view full answer...

Answer 7

The nc code on the Tekonsha Prodigy brake controller indicates that no trailer is connected. When you step on the brake pedal though it should still say that the trailer is not connected. It is possible that there is a short being caused by a dirty…

view full answer...

Answer 8

Hey Randy, If you're getting an 'OL' (overload) error on your Tekonsha BRAKE-EVN Trailer Brake Controller #TK63VR when the trailer isn't connected then you likely have a bad ground on the Excursion. When connected to the trailer…

view full answer...

Answer 9

Anything is possible, including getting you that manual. I've attached the owner's manual for the Tekonsha BRAKE-EVN #TK63VR that you can check out below. Just let us know if you have any other questions.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Location Of Factory Brake Controller Port On 2007 Toyota Tundra SR5 w/ Tow Package

Featured Help Information

Miscellaneous Media

Continue Researching