Replacement 7-Way Trailer Connector-2007 Toyota Tundra

Question

Question:

Hi, Im looking to replace the 7 pin connector for my 2007 Toyota Tundra because some of the internal pins are corroded off and no longer serviceable. The wiring is great and not damaged. Would you have the replacement connector kit? Thanks, Dane

asked by: Dane S

0

Expert Reply:

The Hopkins # HM11143395 you've looked at is the correct replacement 7-way for your 2007 Toyota Tundra.

The installation is pretty simple, you can see the procedure by clicking the provided link and viewing the video showing the harness being installed on a 2008 Tundra.

expert reply by: Mike L

0

Answer 1

We do have a replacement 7-way and 4-way trailer connector for the 2007 Toyota Tundra, but before we can determine which harness will work for your truck, we will need to know what type of plugs your trucks tow package wiring requires and how the…

view full answer...

Answer 2

The controller will actually wake up from sleep mode when the door is opened so that's likely why you still see the blue light on even with the vehicle off and trailer unconnected. This is common for all brake controllers including the Redarc…

view full answer...

Answer 3

The first step I would take would be to check the 30-amp trailer brake controller fuse which is located in the #10 slot on the fuse box under the hood of your 2008 Toyota Tundra. If the fuse is still intact, then you will want to move to the 7-way…

view full answer...

Answer 4

The nc code on the Tekonsha Prodigy brake controller indicates that no trailer is connected. When you step on the brake pedal though it should still say that the trailer is not connected. It is possible that there is a short being caused by a dirty…

view full answer...

Answer 5

Hey Randy, If you're getting an 'OL' (overload) error on your Tekonsha BRAKE-EVN Trailer Brake Controller #TK63VR when the trailer isn't connected then you likely have a bad ground on the Excursion. When connected to the trailer…

view full answer...

Answer 6

Anything is possible, including getting you that manual. I've attached the owner's manual for the Tekonsha BRAKE-EVN #TK63VR that you can check out below. Just let us know if you have any other questions.

view full answer...

Answer 7

You can use a 7-Way and 4-Way connector at the same time just as long as you are not overloading the light circuits. If your camper has a lot of outside lights like running lights, and brake/stop/turn lights then the lights that perform the same…

view full answer...

Answer 8

The connector should be located underneath the dash to the left of the steering column. It may be taped to another wire and tucked up and out of the way. I have linked a video installation of brake controller being installed on a 2007 Toyota Tundra…

view full answer...

Answer 9

Yes there will be a fuse that protects the 12 volt trailer accessory circuit of your 7-way wiring. If this is factory wiring of a truck you'll want to check out the fuse box diagram or the owners manual.

view full answer...

Answer 10

The reverse light pin on a traditional 7-way trailer connector, like part #PK11893 or a factory connector if that's what you have on your 2018 Ram, is the center pin. Take a look at the picture I attached that shows all the pin functions. To add…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Replacement 7-Way Trailer Connector-2007 Toyota Tundra

Featured Help Information

Miscellaneous Media

Continue Researching