Overall Cylinder Length of Replacement Cam Lock Cylinder # 295-000077

Question

Question:

So I read the qanda section about the length but Im not sure what you refer to as the cylinder. Is the length considered from where it seats against the door to the bottom where the screw goes in? Or the entire length of the lock? Do you just have a diagram to make this easier? Thanks

asked by: Travis

0

Expert Reply:

The 1-3/4 inch length of the Replacement Cam Lock Cylinder # 295-000077 refers to the threaded length of the cylinder.

We also have 7/8 inch part # 295-000003.
1-1/8 inch # 295-000004
1-3/8 inch # 295-000005

expert reply by: Jameson C

0

click to enlarge

Answer 1

Replacement Cam Lock Cylinder for RVs, #295-000077 is a 1-3/4" long by 3/4" diameter measured at the threads. The 1-3/4 inch length of the Replacement Cam Lock Cylinder #295-000077 refers to the threaded length of the cylinder. Other…

view full answer...

Answer 2

What I think you are asking for is a combination of replacement locks for entry door and maybe storage compartments, all keyed the same. Please let me know if I am incorrect that I may provide a different recommendation for you. Or, if my suggestion…

view full answer...

Answer 3

We have two sizes of cam lock cylinders close to the length of 1-1/4 inch you listed. We have the part #295-000004 you referenced which is 1-1/8 inch or we have the part #295-000005 which is 1-3/8 inch. You'd need to measure what you have to see…

view full answer...

Answer 4

The Replacement Cam Lock Cylinder #295-000004 is measured at the threads, so you have done it correctly. I went to the warehouse and got the same measurement as your photo, 1-1/8". You would not be able to order these cylinders to match your…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Since RV door latches are basically all pretty universal we do carry replacement cargo door latches like the Global Link RV Baggage Door Slam Latch part #295-000015.

view full answer...

Answer 8

The Replacement Cam Lock Cylinder for RVs #295-000077 is the lock core only. If you are needing the entire lock assembly we have the following options available depending on the size of your lock. Compartment Door Key Lock - 5/8" #372305…

view full answer...

Answer 9

The cylinders for the latches need to be measured for length to get you the correct replacements. This means removing the lock cylinder which should not be difficult if it is able to be removed as some are and some are not. If you disassemble the…

view full answer...

Answer 10

The correct replacement we offer for an AL-KO 568182 or Hayes 09089324 is the Trailer Hub and Drum Assembly part #AKHD-865-7-1-EZ-K which will work with the EZ-Lube Spindles (Dexter) and UltraLube (AL-KO). I can confirm the above will fit an AL-KO…

view full answer...

Answer 11

You are just fine; it will work with the prewiring in your 2019 Lance 855. While correct that a 2.0 will not work with a 1.0 system this is making reference to intermixing the cameras and monitors. The prewire plate on the back of the trailer is…

view full answer...

Answer 12

Yes, it will but you'll need a minimum of 2" between the edge of your hitch receiver and the back of the ball mount face. The etrailer Anti-Rattle Hitch Collar item #e38FV extends out 3/4" from the edge of your hitch receiver, this…

view full answer...