Torque Specifications for 8 Inch Wheel on 1/2 Inch Wheel Studs

Question

Question:

Kenda 8 inch tires mounted on 5 by 4.5 hub with 1/2 lugs, what is the proper torque?

asked by: Tom

0

Expert Reply:

For the 1/2 inch lugs with your 8 inch wheels, you will want to use a torque range of 75 to 85 ft-lbs. I have also attached a helpful image that breaks down the different torque specifications depending on the wheel size/type and stud size that you have.

expert reply by: Chris R

0

click to enlarge

Answer 1

I checked online and it does look like your Triton LTWCI X trailer uses a 5 on 4-1/2 lug pattern. You may want to measure and confirm this. Otherwise the Kenda 4.80-12 Bias Trailer Tire with 12" White Wheel - 5 on 4-1/2 - Load Range B item…

view full answer...

Answer 2

It is certainly possible for any axle to wear out enough over time to need replacing. Since the suspension is built into a torsion axle if the suspension part was to wear out pretty much the only solution would be to replace the axle. If the…

view full answer...

Answer 3

I attached a chart that has all of the recommended lug nut torque specs for trailer wheels. Based on your studs being 1/2 inch, your wheels being 15 inches in diameter, and your lug nuts being coned you would want to torque your lug nuts to 90-120 ft…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Torque Specifications for 8 Inch Wheel on 1/2 Inch Wheel Studs

Product Page this Question was Asked From

Continue Researching