How to Determine if Trailer Hub # 8-259-50UC1-EZ Fits 2001 Triton XT Trailer

Question

Question:

Will your # 8-259-50UC1-EZ hub fit my 2001 Triton XT-10-101trailer?

asked by: Kirk W

1

Helpful Expert Reply:

If your trailer has spindles that are 1.06 inch in diameter where the bearings ride the part # 8-259-50UC1-EZ will fit and work well as that is the standard dimension for 2,200 lb axles spindles like what this is intended for.

expert reply by: Jameson C

1

Answer 1

The hub assembly we offer for a 2,200-lb EZ-Lube axle is part #8-259-50UC1-EZ. This hub has a zinc plating that makes it great for snowmobile trailers or boat trailers. The Inner bearing and race, outer bearing and race, grease seal, grease cap, and…

view full answer...

Answer 2

The Trailer Idler Hub Assembly for 2,000-lb E-Z Lube Axles - 5 on 4-1/2 - Galvanized #AKIHUB-545-2-G-EZ-2K and the Trailer Hub Assembly - 2,200-lb E-Z Lube Axles - 5 on 4-1/2 - 8" - 12" Wheels - Galvanized #8-259-50UC1-EZ are interchangible…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

How to Determine if Trailer Hub # 8-259-50UC1-EZ Fits 2001 Triton XT Trailer

Product Page this Question was Asked From

Continue Researching