Wiring Diagram for Lippert Stabilization Jack LC298707

Question

Question:

What is the wiring diagram for the LC298707. There are no instructions or diagram to show the wiring schematic.

asked by: Ed M

0

Expert Reply:

I have included a picture showing how the motor and switch wire up on the Lippert stabilizer jack # LC298707.

expert reply by: Michael H

0

click to enlarge

Richard V.

8/8/2020

I have a 2014 jayco eagle 27.5 with the lippert electric jack, my wiring fell off at the vinyl coating at the connectors, will like to know if a wiring diagram is available please note a also have a remote that powers jacks all the wiring diagrams have only a switch and power. What I'm looking for a a diagram that shows the wiring that includes the wires for a remote. Thanks,

Reply

Jon G.

8/18/2020

Since it sounds like your stabilizer system is connected to a larger section of your Jayco you might need to reach out to Jayco directly to see if they have a specific wiring diagram for your application. The only stabilizers we have include the High-Speed # LC298707 which comes with the switch, and the Ground Control TT # LC672136 which does come with a controller, but all of the connections are plug and play.

Reply

Richard V.

8/18/2020

@JonG Thanks for you're response, the wires are not plug and play, they are joined by metal wire nuts, that's why they rusted apart, the reason I sent you this problem is the advise from Jayco because they don't have a drawing, now I'm in a pickle. The drawing above would be a simple fix but would not operate my remote

Reply

Jon G.

8/28/2020

@RichardV I'm sorry to hear that. I wish that wiring diagrams were universal with colors and everything but unfortunately they are not. I'd try checking some of the forums that are dedicated for Jayco owners to see if someone could send you a pic of their setup if what you're trying to connect is OEM.

Reply

Answer 1

For your Lippert Components Power Stabilizer Trailer Jack #LC298707 the wiring is pretty simple. There are two wires that come out of the motor and they are both used as power or ground depending on the direction you want to turn the motor. To…

view full answer...

Answer 2

The Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 4-Point Set #LC358590 has 4 35-amp fuses located on the controller. Attched is a complete wiring diagram for you to check out.

view full answer...

Answer 3

When your Lippert Ground Control 3.0 #LC358590 has a reading that says "Comm Error" it is referring to the communication between the controller and touch pad. You will need to check your harness to ensure it is connected properly and there…

view full answer...

Answer 4

I have attached some diagrams of the wiring for the Lippert Replacement Hydraulic Power Unit with 2-Quart Pump Reservoir Kit for RV Slide-Out IRC System #LC141111. The first one is from my contact at Lippert and some of the extra wiring is from their…

view full answer...

Answer 5

We have just what you need to get this job taken care of. There are two wiring kits you will need, the Curt T-Connector #C56327 and the Universal Installation Kit #ETBC7. These two kits combined will include everything you need to install a 7-way on…

view full answer...

Answer 6

In order to test the controller on the Lippert Ground Control 3.0 Electric Leveling System you'll first need to obtain a multimeter. Once you have this then you will need to use the ground probe and place that on the green wire coming from the…

view full answer...

Answer 7

I sent all of this to my tech contact at LCI to see what they this is the problem and they were able to come up with a way to use the voltage readings to determine where the issue is: There are 4 wires on the harness as follows Black= power (need to…

view full answer...

Answer 8

I have included a picture showing how the motor and switch wire up on the Lippert stabilizer jack #LC298707.

view full answer...

Answer 9

It appears that all you going to need is the Replacement Lippert 4-Point Leveling System Control Brain Wiring Harness #LC178278. This wiring harness will allow you to plug your new Replacement Lippert Leveling Control Brain for 4-Point Leveling…

view full answer...

Answer 10

The power circuit for each leg of the Lippert Ground Control leveling system #LC358590 is protected by a 35 amp fuse. That means that at most the entire unit could draw up to 140 amps at a time. Realistically it would probably be considerably less…

view full answer...

Answer 11

We have heard of this issue before on the Lippert Ground Control systems #LC358590. Here is the recommended procedure for clearing the error code: Extend all jacks at least 6 inches. Then press and hold the RETRACT button until the jacks begin…

view full answer...

Answer 12

Hey Mark, sorry to hear about the trouble you're having! There are 3 things to check when you get the comm error on your Lippert Ground Control system; the touch pad, the controller, and the wiring that connects the two. Since you've already…

view full answer...

Wiring Diagram for Lippert Stabilization Jack LC298707

Continue Researching