Mounting 1/4 Inch Cable to Hand Winch

Question

Question:

Will the Item # DL24350 cable keeper work for 1/4 in stainless steel on my winch?

asked by: Mike

0

Expert Reply:

The Cable Clamp for Pulling and Brake Winches by Dutton-Lainson # DL24350 is compatible with 1/4 inch stainless Steel winch cable like the Hand Winch Cable with Safety Hook 1/4" Diameter x 50' Long - 3,500 lbs # DL24104.

You can also use the Cable Fastener for 1/4", 9/32" and 5/16" Cable and Heavy Duty Winches # DL24362 or the Cable Fastener for 3/16", 7/32", and 1/4" Cable and Medium Duty Winches # DL24361 to fit your 1/4 inch cable.

expert reply by: Jason S

0

Answer 1

On the Dutton-Lainson Cable Clamp #DL24350 the hole diameter is 1/4-inch and the overall dimensions are 1-1/4 x 3/4-inch.

view full answer...

Answer 2

The small plate you are referring to in the photo of the Dutton-Lainson Hand Winch #DL14825 is the Cable Clamp for Pulling and Brake Winches by Dutton-Lainson #DL24350. The winch does come with this cable clamp, but it does not come with a cable or…

view full answer...

Answer 3

The correct cable with hook for the Dutton-Lainson Hand Winch #DL15440 is the #DL24104. This is a 50 foot long 1/4 diameter galvanized aircraft cable with safety hook. The cable fastener you will need for this is the #DL24362 which is sold separately…

view full answer...

Answer 4

I have a solution for you, and you can use ratchet straps to support your boat once you have it in the air. However, we do not recommend raising or lowering the boat with ratchet straps. The ratchet straps are rated for use as tie-downs, not as…

view full answer...

Answer 5

The Fulton High-Performance 2-Speed Trailer Winch #F142430 referenced in your question is designed to be used with 7/32 inch cable. I spoke with my contact at Fulton and he does not recommend using 5/16 inch cable on this drum. For a similar hand…

view full answer...

Answer 6

The Dutton-Lainson Hand Winch #DL15721 is their highest capacity DLB series winch with rated capacity of 2,500lbs. You would then need the Removable Handle Kit #DL6454 along with the Drill Drive Socket Adapter #DL6456 to use a drill to operate the…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hey Nathan, the PowerMax panels like the part #PM59VR that you referenced use 12- VAC residential style miniature circuit brakers. Typical brands are ITE/Siemens, Murray, Crouse-Hinds, and Thomas & Betts.

view full answer...

Mounting 1/4 Inch Cable to Hand Winch

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching