Rail Dimensions Reese Fifth Wheel Hitch RP30047 is Designed to Fit

Question

Question:

Existing rails. Please give me the dimensions of a Reese fifth wheel hitch number RP30047 want to make sure it slips into my existing rails thank you

asked by: Victor C

0

Expert Reply:

The Reese Fifth Wheel hitch part # RP30047 is designed to fit the industry standard style of fifth wheel rails that are very common and are spaced 22 inches apart.

I attached a picture that shows the dimensions of the rails this hitch is designed to fit.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Curt is the manufacturer of the Mopar branded 5th wheel trailer hitches. For example, the Mopar 5th Wheel Trailer Hitch part 82214742 is the same as the Curt Q20 5th Wheel Trailer Hitch part #C16530-16021 and the Mopar 5th Wheel Trailer Hitch part…

view full answer...

Answer 2

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 3

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 4

The positioning of the factory fifth wheel installation pucks in your 2020 Ram 2500 has not changed since its inception. Side to side center to center, the pucks will be 39 inches apart. Front to back, center to center will measure 30-3/8 inches. In…

view full answer...

Answer 5

It sounds like you could have a set of standard fifth wheel rails that most manufacturers use for their fifth wheel hitches to install into. The different manufacturers all make their own brand of rail kit, but they all have basically the same…

view full answer...

Answer 6

I have a solution for you on this, but the Mopar hitch for the Ram OEM pucks is not compatible with a Sidewinder style pin box; it's really just a re-branded Curt Q20 head #C16530 so the spherical axial bearing that it has won't work with a…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Rail Dimensions Reese Fifth Wheel Hitch RP30047 is Designed to Fit

Continue Researching