Video Guide for Using Fish Wire to Install Trailer Hitch

Question

Question:

Putting Draw-Tite 65025 on my 2001 Ford F-150 today. I think I have it figured out but was wondering if you have a video. Have not been able to find one featuring the 65025. Or something close that uses the pull wire. thanks

asked by: Scott S

0

Expert Reply:

I really wish we had the chance to install that hitch, but at this time we haven't so we don't have any install videos for it.

I did attach a video below that shows how the fish wire technique is used that should still be helpful.

expert reply by: Jameson C

0

Answer 1

For your 2003 Ford F-150 4x4 the Draw Tite front hitch part #65025 is a confirmed fit so what I suspect is going on is that your hitch was bent in shipping which unfortunately isn't uncommon. What you can do is bend the hitch back using an open…

view full answer...

Answer 2

If you wish to retain the front tow hooks on your 1998 Ford F-150 then you are going to want to use the Curt Front Mount Trailer Hitch Receiver part #31049, not the Draw-Tite Front Mount Trailer Hitch Receiver part #65025. The reason for this is that…

view full answer...

Answer 3

For installation of front hitch #65025 for your 2001 Ford F-150 there are certain holes you will need to use depending on the vehicle. For 1999 and newer F-150 4x4s, Light Duty F-250 models, and Expedition models you would use the lower holes in the…

view full answer...

Answer 4

The Draw-Tite Front Mount Trailer Hitch Receiver #65025 is the correct fit for your 2001 Ford F-150. I do understand your confusion as this receiver does use multiple mounting holes for different model years and the instructions do not include photos…

view full answer...

Answer 5

Both the Curt front hitch #31038 and the Draw-Tite front hitch #65025 will have the receiver below the front fascia. There are no front mount hitches that exist any higher on the 2003 Ford F-150 4x4. I have included a picture showing where the…

view full answer...

Answer 6

For your 2003 Ford F-150 4WD without tow hooks the only front hitch solution we offer that's confirmed as a fit is the Draw Tite part #65025 which will work well.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Video Guide for Using Fish Wire to Install Trailer Hitch

Featured Help Information

Miscellaneous Media

Continue Researching