How to Determine if the Dutton-Lainson Rocker Roller # DL21562 Will Fit an E Z Loader Trailer

Question

Question:

would like to know if this product will work on my trailer. And do you sell all the parts needed to install new rollers.ie washers, pins, etc.

asked by: Mark J

0

Expert Reply:

You will need to measure the rollers that are on your EZ Loader trailer to determine if the Dutton-Lainson Rocker Roller, part # DL21562 will fit.

The Rocker Roller # DL21562 has a diameter of 4-1/4 inches and a length of 4-1/4 inches. They are designed to fit on a 3/4 inch shaft.

I also have the Dutton-Lainson Rocker Roller, part # DL21564. This roller has a diameter of 4-3/8 inches and a length of 3 inches. It will also fit a 3/4 inch shaft.

I do not have any parts available to install the smaller Rocker Rollers.

expert reply by: Jeff D

0

Answer 1

Since your main concern is the marks on the hull of your boat I recommend going to the Yates TPR Ribbed Wobble Roller. These rollers are constructed of thermal-plasticized rubber which is a non-marking, non-scratching material. It is stronger and…

view full answer...

Answer 2

Since the Yates Wobble Roller #YR530R-6P you mentioned is made for a 3/4" bolt it may not be ideal for that application. Instead I recommend the #YR530R-5P which is the same 5" x 3" roller but made to fit a 5/8" bolt. Provided the…

view full answer...

Answer 3

Most boat trailer bow and keel rollers do use pal nuts like #CE10801 to secure the rubber roller to the support shaft and mounting bracket. From your photo I cannot tell quite what type of set-up you have. Since most of our rollers use galvanized…

view full answer...

Answer 4

The Yates Ribbed Wobble Roller #YR500YW-6P has a bushings that measures 3/4" inner diameter the whole way through so it will reflect the angle of the shaft you're needing to install it on, so it will work great for your application as long…

view full answer...

Answer 5

A pal nut is not re-usable, so there is no need to be overly gentle when removing it. Simply grab the nut with a pair of pliers and bend it off. Once you apply a bit of pressure, the nut will bend which will allow you to easily remove it. We offer…

view full answer...

Answer 6

Looks like you have the Yates Ribbed Wobble Rollers part #YR530R-6P installed on your Shoreline boat trailer. We do not carry any pieces that are internal of the roller like a bushing if that is what you are referring to. We carry the retainer rings…

view full answer...

Answer 7

At one time, wobble roller was a patented term, but now the term wobble roller and rocker-roller are interchangeable. The #DL21564 roller you mentioned has an integrated bushing that makes the roller track straight on the shaft it's installed on,…

view full answer...

Answer 8

We carry wobble rollers with a few different inner diameters. What you will need to do is measure the inner diameter of the ones you currently have as well as the outer diameter of the roller and then check out the link I attached to see all of the…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

How to Determine if the Dutton-Lainson Rocker Roller # DL21562 Will Fit an E Z Loader Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching