Dexstar Steel Mini Mod Trailer Wheel - 15 x 5 Rim - 5 on 4-1/2 - Silver Powder Coat

Question

Question:

Thanks Jameson, here is the information your requested, The tires are 205/.75R15 The rime is a 5 on 4.5 with an approximately 3 inch center This wheel is tough getting off due to the clearance between the camper wall and the center hub. Thank you for your help. Regards,

asked by: Don

0

Expert Reply:

Most likely these wheels would fit, but before we get ahead of ourselves...what size tire is on the trailer currently? How many lugnuts hold the wheel to the trailer? Can you get me the bolt pattern? With that info I can get you the best possible wheel and tire solution for your setup.

expert reply by: Jameson C

0

Don

10/10/2017

Thanks Jameson, here is the information your requested, The tires are 205/.75R15 The rime is a 5 on 4.5 with an approximately 3 inch center This wheel is tough getting off due to the clearance between the camper wall and the center hub. Thank you for your help. Regards,

Jameson C.

10/10/2017

Yes, the part # AM20436 will work well as a replacement for what you have. Bolt pattern is right, the pilot diameter right and the diameter is correct. Then for a tire you'd want be the part # LHWL300. This is a Load Range D with a 2,150 lbs at 65 psi capacity, a speed rating of 75 mph and a 2 year roadside assistance program.

Answer 1

The correct set of replacement brake assemblies for your AxleTek 12 inch assemblies is the kit part #AKEBRK-7-SA that you referenced. This kit is a pair of left and right assemblies that are an exact match to what you have that are also self…

view full answer...

Answer 2

We definitely have a wide selection of baby moon caps here at etrailer. As far as brands, we carry Americana and Phoenix baby moons like the Phoenix USA Baby Moon Hubcap - 8-7/8" Diameter - 4 Spline #PXQ1401B and the Americana Baby Moon Trailer…

view full answer...

Answer 3

We have exactly what you are looking for. Based on the part number you found on the sticker of your braking assembly you will need the Electric Trailer Brake Assembly LH #AKEBRK-7L-SA and RH #AKEBRK-7R-SA. These will be an exact replacement for your…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Dexstar Steel Mini Mod Trailer Wheel - 15 x 5 Rim - 5 on 4-1/2 - Silver Powder Coat

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching