How to Tell Which Wheel Tray Holder of a Yakima Two Timer or Four Timer Needs Replacing

Question

Question:

I lost two of my trays because I didnt tighten them down but Im not sure if I need to buy an A tray or B tray. How do I tell? Thanks!

asked by: Annie

0

Expert Reply:

I attached a picture that shows a TwoTimer labeled with what each of the wheel holder types is.

For an A holder you'd need the # 8880796 or for a B you'd need the part # 8880797.

expert reply by: Jameson C

0

click to enlarge

Answer 1

According to Yakima, the difference between the Replacement "A" Wheel Tray Assembly #8880796 and Replacement "B" Wheel Tray Assembly #8880797 is the following: "Look at the base of the wheel cup and look at the cut out above…

view full answer...

Answer 2

It sounds like you are wanting to alter a Swagman XC #S64650 rack to accommodate a recumbent bike, is that correct? Swagman does offer a replacement fold down arm, but it would simply be a replacement for the original arm, and would not be long…

view full answer...

Answer 3

If it's the buckle assembly you'd have to replace the entire cradle like with the part #8880797 or the #8880796 depending on which cradle it is. If it was actually the strap the part number you need is the #Y8880229.

view full answer...

Answer 4

I'd be happy to help out! The way to choose correctly between the Replacement "A" #8880796 and "B" #8880797 trays for your Yakima FourTimer is how many bumps you'll find at the base of the wheel cup "(or tray). Our…

view full answer...

Answer 5

We do have the A replacement Yakima TwoTimer bike rack with the part #8880796.

view full answer...

Answer 6

We have the wheel mounting hardware #8880520 for the Yakima TwoTimer. The wheel tray has been replaced with #8880796 which is what you'd need.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

How to Tell Which Wheel Tray Holder of a Yakima Two Timer or Four Timer Needs Replacing

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching