Which Bearing Buddy for Harbor Freight Trailer 62648 & 62666

Question

Question:

These are the 1195lb capacity trailers they sale.

asked by: Trevor

0

Expert Reply:

The Bearing Buddy we have found that fits most of the Harbor Freight trailers is the part # BB2047 which would be the correct one for if your hub bore was 2.047 inches.

I'd recommend verifying that measurement on your trailer hub bore.

expert reply by: Jameson C

0

Answer 1

In order to pick out the correct bearing buddy you will need know the pilot hole of your hub. To do this, remove the wheel and tire and remove the grease cap from the center of the hub. Usually it is a metal cap that is just lightly hammered into…

view full answer...

Answer 2

Your 1195 Haul-Master trailer should have a BT8 spindle which means you need the kit #RG04-020 for standard caps, the kit #RG04-040 for EZ Lube caps, or the kit #BB1980A which is the Bearing Buddy kit with the auto check in place. Attached is a video…

view full answer...

Answer 3

From our experiences the Harbor Freight trailers like yours have a hub bore that requires a cap or Bearing Buddy that measures 2.047 inches like the #BB2047 you referenced. We don't have a standard cap that fits this size so the Bearing Buddy is…

view full answer...

Answer 4

We often hear of weak customer support and limited spare parts availability with "bargain" trailer manufacturers. I found an online copy of the owner's manual for the Harbor Freight Haulmaster utility trailer model 90154 but it includes…

view full answer...

Answer 5

Believe it or not, the outside diameter of the Bearing Buddy is designed to be a bit larger than the inside diameter of the hub bore. Typically, a Bearing Buddy sized to fit a 1.98 hub bore will actually be about 1.986 in diameter, which means yours…

view full answer...

Answer 6

You should be able to make your Bearing Buddy Bearing Protectors #BB37SR fit by placing them in the freezer. The cold temperatures will cause the steel to shrink slightly but they will likely have to sit in the freezer overnight to ensure they get…

view full answer...

Answer 7

Hubs will heat up when driving, but if it feels like they are getting too hot, then you will want to look at a few things on your hub. My guess is that the spindle nut is too tight and the added stress on the bearings is overheating the bearings and…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Which Bearing Buddy for Harbor Freight Trailer 62648 & 62666

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching