Replacement Grease Cap for 1195 Haul-Master Trailer From Harbor Freight

Question

Question:

Do you have the dust cover wheel bearing cap for the 1195# Harbor freight Hual Master trailer?

asked by: Clayton P

0

Expert Reply:

Your 1195 Haul-Master trailer should have a BT8 spindle which means you need the kit # RG04-020 for standard caps, the kit # RG04-040 for EZ Lube caps, or the kit # BB1980A which is the Bearing Buddy kit with the auto check in place.

Attached is a video for you to check out.

expert reply by: Jon G

0

Answer 1

From our experiences the Harbor Freight trailers like yours have a hub bore that requires a cap or Bearing Buddy that measures 2.047 inches like the #BB2047 you referenced. We don't have a standard cap that fits this size so the Bearing Buddy is…

view full answer...

Answer 2

The Bearing Buddy we have found that fits most of the Harbor Freight trailers is the part #BB2047 which would be the correct one for if your hub bore was 2.047 inches. I'd recommend verifying that measurement on your trailer hub bore.

view full answer...

Answer 3

Believe it or not, the outside diameter of the Bearing Buddy is designed to be a bit larger than the inside diameter of the hub bore. Typically, a Bearing Buddy sized to fit a 1.98 hub bore will actually be about 1.986 in diameter, which means yours…

view full answer...

Answer 4

The Dexter Trailer Idler Axle w/ Hubs - EZ-Lube - 5 on 4-1/2 Bolt Pattern - 60" Long - 2,200 lbs #20545I-EZ-60-15 is a great starting point to upgrade your trailer. This will give you a standard size axle with good bearings, hubs, and EZ-lube…

view full answer...

Answer 5

You should be able to make your Bearing Buddy Bearing Protectors #BB37SR fit by placing them in the freezer. The cold temperatures will cause the steel to shrink slightly but they will likely have to sit in the freezer overnight to ensure they get…

view full answer...

Answer 6

In order to pick out the correct bearing buddy you will need know the pilot hole of your hub. To do this, remove the wheel and tire and remove the grease cap from the center of the hub. Usually it is a metal cap that is just lightly hammered into…

view full answer...

Answer 7

We get the Curt hitch part #C12304 directly from Curt and I can guarantee it's not a knock-off brand.

view full answer...

Answer 8

We offer quite a few different plastic trailer fenders that will work with the 12" wheels on your 4x8 Harbor Freight trailer like the Single Axle Trailer Fender #PF775X21W, but all of our fenders will require a mounting bracket and will not be…

view full answer...

Answer 9

From what I could find, the Harbor Freight trailers do say not to exceed 45 miles per hour in the owners manual. That being said, the tires they use are not rated very high and may be the limiting factor. The trailer you have looks to use a 5 on 4…

view full answer...

Answer 10

I have attached a link to the trailer fenders we offer. You can use the menu on the page to select the fender based on the size tire, material, color, and how it is attached. If you are looking for just a fender and do not intend to use it for a step…

view full answer...

Answer 11

Hubs will heat up when driving, but if it feels like they are getting too hot, then you will want to look at a few things on your hub. My guess is that the spindle nut is too tight and the added stress on the bearings is overheating the bearings and…

view full answer...

Answer 12

We have found that the Bearing Buddy part #BB2047 fits several Harbor Freight Trailers. Including the following trailers 90154 42709 90153 42708 2575 2948 Or, you can measure the bore of your hub where the cap would go with a digital caliper like…

view full answer...

Replacement Grease Cap for 1195 Haul-Master Trailer From Harbor Freight

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching