1990 Chevy Silverado with Roll Pan Bumper Trailer Hitch Recommendation

Question

Question:

Need tow hitch for my truck. Which one will work???

asked by: Chris H

0

Expert Reply:

For your 1990 Chevy truck with a roll pan bumper what you will want is the Draw Tite hitch part # 41522 which is a confirmed fit.

expert reply by: Jameson C

0

click to enlarge

Paul C.

5/9/2020

I need a hitch for my Cheyenne 93 step side has roll pan bumper thanks

Chris R.

5/12/2020

As long as it's the 1500 model, the Curt Class III Trailer Hitch # 13942 will fit your 1993 Chevy C/K Cheyenne with the roll pan bumper perfectly.

Answer 1

I can understand how the wording could be confusing on whether or not the Curt #C94FR (56429) will work on your 2020 GMC Terrain, but I can confirm that it will indeed work for you without needing to install any extra fuses or relays on the vehicle.…

view full answer...

Answer 2

The Curt Vehicle Wiring Harness #C94FR that you referenced is supposed to be used if your 2019 GMC Terrain came with the factory tow package. If those fuse locations are empty, then it sounds like you don't have the factory tow package. As of…

view full answer...

Answer 3

Bracket height is the height of the jack from the center of the mounting bracket to the bottom of the jack when retracted and extended. In this case this jack #BD195356 is 15-1/8" Retracted and 30-1/8" Extended. From the top of the jack to…

view full answer...

Answer 4

The brake controller adapter, like part #3065-P for a Tekonsha brake controller like the P2 #90885, installs at the connector which is located behind the storage pocket that is built into your center dash right above the ashtray (see attached…

view full answer...

Answer 5

Trailer brake controller wiring harness #3065-P is the correct harness for your 2006 Ford F-450. In your picture, it would plug into the larger one on the right. The larger square end of the harness plugs into your truck's connector and the small…

view full answer...

Answer 6

We do have a custom fit hitch option for the 1989 Chevy C/K Series. I recommend Draw-Tite Ultra Frame Trailer Hitch Receiver part #41938 if you have a standard or step bumper. The Draw-Tite hitch is rated for 12,000 lbs gross towing weight and will…

view full answer...

Answer 7

Yes, there is 15 teeth per each gear on the Replacement Gear Kit for etrailer and Ram Sidewind Jacks #TJA-2000S-GR. These gears have a thickness of 0.5", an OD of 1.36", and an ID of 0.5".

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

1990 Chevy Silverado with Roll Pan Bumper Trailer Hitch Recommendation

Continue Researching